PWB

Links

• https://bitbucket.org/teamalphag/pwb_rev1_firmware
• https://edev-group.triumf.ca/fw/exp/alphag/feam/rev1
• https://edev-group.triumf.ca/hw/alphag/feam/rev1
• https://ladd00.triumf.ca/daqinv/frontend/list/170 - PWB inventory database

Schematics

• File:Pwb rev0.pdf
• File:Pwb-rev1-after.pdf
• File:AlphaG Rev1.pdf

Manuals

• File:AFTER MANUAL V1.pdf AFTER SCA manual v1
• File:AFTER DataSheet1 1.pdf AFTER SCA manual v1.1
• File:AFTER SCA table2.pdf AFTER SCA channel map

Firmware

NIOS terminal

$ ssh agmini@daq16
$ /opt/intelFPGA/16.1/quartus/bin/jtagconfig
1) USB-Blaster [2-1.2]
  02B030DD   5CGTFD7(B5|C5|D5)/5CGXBC7B6/..
$ /opt/intelFPGA/17.0/quartus/bin/nios2-terminal
nios2-terminal: connected to hardware target using JTAG UART on cable
nios2-terminal: "USB-Blaster [2-1.2]", device 1, instance 0
nios2-terminal: (Use the IDE stop button or Ctrl-C to terminate)
PWB Revision 1 Boot Loader
Ver 2.0  Build 357 - Wed Jun  6 15:05:35 PDT 2018
...

Flash boot loader firmware via jtag

$ ssh agmini@daq16
$ /opt/intelFPGA/16.1/quartus/bin/jtagconfig
1) USB-Blaster [2-1.2]
  02B030DD   5CGTFD7(B5|C5|D5)/5CGXBC7B6/..
$ cd ~/online/firmware/pwb_rev1
$ ls -l
$ /opt/intelFPGA/17.1/quartus/bin/quartus_pgmw
... auto detect
... load the jic file
... in menu tools->programmer, enable "unprotect device"
... start program/configure operation

Flash user page firmware via esper-tool

$ ssh agmini@daq16
$ cd online/src
$ more update_pwb.perl ### check that $fw is set to the desired firmware file
$ ./update_pwb.perl pwb06 ### or give more PWB names or give "all"

Build firmware

NOTE: quartus 16.1 should be used for jtag (jtagconfig and jtagd)

NOTE: quartus 17.0 should be used to build the PWB firmware (17.1 is not compatible)

$ ssh agmini@daq16
$ /opt/intelFPGA/17.0/nios2eds/nios2_command_shell.sh
------------------------------------------------
Altera Nios2 Command Shell [GCC 4]

Version 17.0, Build 602
------------------------------------------------
$ cd online/firmware/git/pwb_rev1_firmware
$ git pull
$ git checkout alphag
$ git pull
$ ./scripts/compile_project.sh
$ ls -l bin/*.sof bin/*.jic bin/*.rpd
-rw-r--r-- 1 agmini alpha 12727389 Jan 24  2018 bin/feam_auto.rpd
-rw-r--r-- 1 agmini alpha 33554661 Jan 24  2018 bin/feam.jic
-rw-r--r-- 1 agmini alpha  6974754 Jan 24  2018 bin/feam.sof
$ ### feam.jic is loaded via jtag
$ ### feam_auto.rpd is loaded via esper
$ ### feam.sof is used to attach the signal tap

ESPER Variables

• Board
  • invert external trigger - invert trigger signal from CDM before it drives any logic (to undo incorrect signal polarity)

• Link
  • link_ctrl bits:

0 - sata_link_udp_stream_in_enable - permit data flow from sata link to OFFLOAD_SATA
1 - udp_stream_out_enable - permit sca data flow to sata link
2 - sata_to_eth_enable - permit ethernet data flow from sata link to TSE_MAC
3 - eth_to_sata_enable - permit ethernet data flow from TSE MAC to sata link
4 - sink8_delay - (temporary) change sink8 ready latency in link_tx
5 - stop_our_tx - (temporary) manually activate the flow control signal into link_tx
6 - stop_remote_tx - (temporary) manually activate the flow control signal into link_tx

ZZZ

ZZZ