PcHardware: Difference between revisions

From DaqWiki
Jump to navigation Jump to search
Line 53: Line 53:
* RAM: 1 (32GB) kit of 4x8GB DDR3-1600 RAM : http://www.ncix.ca/products/?sku=65663&vpn=F3-12800CL10Q-32GBZL&manufacture=G%2ESkill http://www.ncix.com/detail/g-skill-ripjawsz-f3-12800cl10q-32gbzl-32gb-4x8gb-dc-65663.htm
* RAM: 1 (32GB) kit of 4x8GB DDR3-1600 RAM : http://www.ncix.ca/products/?sku=65663&vpn=F3-12800CL10Q-32GBZL&manufacture=G%2ESkill http://www.ncix.com/detail/g-skill-ripjawsz-f3-12800cl10q-32gbzl-32gb-4x8gb-dc-65663.htm
* Video card: none, using Intel on-CPU video
* Video card: none, using Intel on-CPU video
* replacement for stock cooling fans, 2 per computer (1 rear case fan, 1 front disk drive fan, mount for air flow back to front of computer - rear fan pushes air into computer, front fan pushes air into hard disk enclosure, out of computer; remove stock Sonata3 fan, remove front air filter, duck-tape closed all rear and side case openings - except for rear fan intake and front fan exhaust through front panel louvers) : for fans, use PWM or non-PWM fans from list above.
* Cooling fans: (replace stock short-life-time fans) - 2 per PC - http://www.ncix.com/detail/noctua-nf-s12a-flx-120mm-ultra-b4-79670.htm
* gotcha: the 4-pin fan headers do not provide PWM fan control (see mobo manual - pwm pin is hardwired to +5V) - use non-PWM fans (3-pin connector). The 4-pin fan header CPU_OPT has PWM control - connect a PWM fan (4-pin connector) - but it will run at same speed as the main CPU fan.
* Instructions for mounting cooling fans: remove stock short-life-time fans, mount replacement fans for air flow from back to front of the case: 1 rear case fan, 1 front mounted fan blowing on the hard drives. Remove front air filter, duct-tape shut all rear, side and bottom air holes - air flow should be: rear fan pushes air into computer, front fan pushes air into hard disk enclosure, out of computer through the front of the case where the air filter used to be.
* Cooling fans note: ASUS Z87 WS motherboard requires use of non-PWM fans. The 4-pin fan headers do not provide PWM fan control - see mobo manual - pwm pin is hardwired to +5V. Only the 4-pin fan header CPU_OPT has PWM control - connect a PWM fan (4-pin connector) - but it will run at same speed as the main CPU fan.


=== Version 2014-MAY-8 Intel Socket 2011 ===
=== Version 2014-MAY-8 Intel Socket 2011 ===

Revision as of 13:08, 9 May 2014

DAQ PC Configurations

Standard components

Fans

Power supplies

Power supply requirements:

  • 120mm cooling fan (longer life, better air flow vs small fans)
  • ActivePFC (no 110/220V switch, high power factor required for use with UPSes)
  • 4 or more SATA power connectors

SSD

  • Kingston V200, V200+, V300 - 60GB, 120GB

Obsolete items

Version 2014-May-07 Reduced cost PC (Preliminary)

Version 2014-MAY-8 Intel Socket 1150 (Preliminary)

Version 2014-MAY-8 Intel Socket 2011

Version 2012-OCT-4 AMD-E450 reduced cost PC (PRELIMINARY)

Version 2011-SEP-05 AMD-E350 reduced cost PC

Version 2011-OCT-31 Intel Socket 1366

Version 2011-FEB-08 Intel Socket 1366

Version 2010-May-13 Intel Socket 1156

Version X Intel Socket 775

  • mobo: ASUS P5B-VM
  • CPU: Intel dual core 2.4 GHz
  • RAM: DDR2-800
  • SATA disks

Version X AMD AM2/AM3

  • mobo: ASUS Crosshair and Crosshair II
  • CPU: assorted multicore socket AM2/AM3 CPU
  • RAM: DDR2-800

Version X AMD Socket 939

  • mobo: ASUS A8N-E
  • CPU: AMD assorted socket 939 1-2 core CPUs
  • RAM: DDR400 UDIMMs up to 4x1GB=4GB total
  • up to 4x SATA disks

Version X AMD Dual Socket 940

  • mobo: assorted supermicro, asus, msi
  • CPU: AMD Opteron Socket 940 assorted speed grades
  • RAM: registered and registered+ECC DDR400

Version X AMD Dual Socket A

  • mobo: ASUS A7M266-D
  • CPU: dual Athlon-MP 1.8-2.2 GHz
  • RAM: DDR266

Version X Intel Dual Pentium3

  • mobo: ASUS CUV4X-D
  • CPU: dual Pentium3 1GHz
  • RAM: SDR133

Version X Intel Dual Pentium2 ISA

  • mobo: ASUS P2B-D
  • CPU: dual slot Pentium2 400-800 MHz
  • RAM: SDR100, SDR133