Ubuntu: Difference between revisions

From DaqWiki
Jump to navigation Jump to search
Line 144: Line 144:
cd scripts
cd scripts
git pull
git pull
</pre>
== disable swap (debian 11) ==
* on 64 GB RAM machines swap is not useful
* on machines booted from network (NFS-ROOT), swap does not work
* on machines running from flash (RPi, etc), flash is too slow for useful swap.
<pre>
systemctl disable dphys-swapfile
systemctl stop dphys-swapfile
dphys-swapfile uninstall
</pre>
</pre>


Revision as of 10:59, 21 December 2021

About Ubuntu

AAA


Ubuntu version

lsb_release -a
uname -a

Ubuntu installer

  • updated for Ububtu LTS 20.04.01
  • download the latest Ubuntu LTS desktop installer iso image
  • dd the image to a USB key
  • power down, disconnect all disks (all HDDs, all SSDs, all M.2)
  • connect the SSD to be used as system disk
  • if system will use mirrored SSDs (using ZFS mirror), leave second SSD disconnected, we will activate it later
  • power up
  • boot from USB key in legacy mode or UEFI mode (select this in the BIOS boot menu - F8 for ASUS, F11 for Supermicro)
  • follow the instruction:
  • "try ubuntu or install ubuntu" - choose "install"
  • select language - accept default
  • "updates and other software" - accept default settings ("normal install")
  • "installation type" - select "advanced features" and "experimental: use ZFS"
  • accept partition choice
  • "where are you?" - select "Vancouver" (PST time zone)
  • "who are you?" - leave all fields blank, except "username" set to "wheel", "password" set to the root password. hostname will be set later after configuring the network
  • installation runs in a few minutes, when finished, reboot
  • login as user wheel
  • answer annouying questions:
  • "livepatch" - say "next"
  • "help improve" - select "do not send", say "next"
  • "privacy" - leave "location" as "off", say "next"
  • "ready to go", say "done"
  • right-click on the desktop, say "open in terminal", a shell will open
  • say "sudo /bin/bash", enter the root password, you now have the root shell
  • run nm-connection-editor to configure the network
  • after network is up (can ping ladd00), continue with post-installation steps below

Install instructions

prepare

apt-get update
apt-get upgrade

install ssh

apt install ssh

configure hostname

vi /etc/hostname

disable swap

ubuntu installer creates a 2 GB swap partition, not useful on 32-64 GB machine, disable it: 

vi /etc/fstab ### comment out the "swap" line

maybe reboot

this is a good point to reboot the machine to boot the latest kernel and to set the correct hostname

install time synchronization

apt-get -y install chrony
echo server time1.triumf.ca iburst >> /etc/chrony/chrony.conf
echo server time2.triumf.ca iburst >> /etc/chrony/chrony.conf
echo server time3.triumf.ca iburst >> /etc/chrony/chrony.conf
systemctl disable systemd-timesyncd.service
systemctl stop systemd-timesyncd.service
systemctl disable ntp
systemctl stop ntp
systemctl enable chrony
systemctl restart chrony
chronyc sources
chronyc tracking

enable outgoing email (debian 11)

this is different from ubuntu 20. it uses /etc/mailname and it hardwires the hostname into main.cf.

enable outgoing email

dpkg-reconfigure postfix ### or
apt install postfix ### select "satellite system", enter full hostname "xxx.triumf.ca", enter "smtp.triumf.ca"
echo olchansk@triumf.ca >> ~root/.forward
apt-get install -y mailutils
mailx root
test
^D

install missing packages

(apt eats terminal input, even the "yes |" trick does not quite work, repeat the following commands until they report that everything is installed) 

yes | apt -y install ssh tcsh ethtool ncat rsync strace net-tools sysstat smartmontools lm-sensors traceroute time minicom screen git
yes | apt -y install lsb-release
yes | apt -y install flex bison
yes | apt -y install neofetch
yes | apt -y install snmp snmp-mibs-downloader
yes | apt -y install git subversion g++ gfortran cmake doxygen
yes | apt -y install python
yes | apt -y install curl libcurl4 libcurl4-openssl-dev
yes | apt -y install mariadb-client ### mysql client
yes | apt -y install libz-dev sqlite3 libsqlite3-dev unixodbc-dev
yes | apt -y install libssl-dev
yes | apt -y install emacs xemacs21
yes | apt -y install mutt bsd-mailx # email clients
yes | apt -y install liblz4-tool pbzip2
yes | apt -y install libc6-dev-i386 # otherwise no /usr/include/sys/types.h
yes | apt -y install libreadline-dev
yes | apt -y install chromium-browser chromium-codecs-ffmpeg-extra
yes | apt -y install ubuntu-mate-themes
yes | apt -y install libmotif-dev libxmu-dev
yes | apt -y install xfig gsfonts-x11 gsfonts-other # install fonts for xfig
yes | apt -y install libgsl-dev # additional GNU Scientific Library
yes | apt -y install linux-tools-common linux-tools-generic linux-tools-5.4.0-48-generic # cpupower frequency-info
yes | apt -y install linux-image-generic-hwe-20.04 # enable linux 5.11 series

install git/scripts

mkdir ~root/git
cd ~root/git
git clone https://daq00.triumf.ca/~olchansk/git/scripts.git
cd scripts
git pull

disable swap (debian 11)

  • on 64 GB RAM machines swap is not useful
  • on machines booted from network (NFS-ROOT), swap does not work
  • on machines running from flash (RPi, etc), flash is too slow for useful swap.
systemctl disable dphys-swapfile
systemctl stop dphys-swapfile
dphys-swapfile uninstall

install ganglia

yes | apt-get -y install ganglia-monitor
systemctl enable ganglia-monitor

cd ~root/git/scripts
git pull
cp etc/gmond-ubuntu.conf /etc/ganglia/gmond.conf
systemctl restart ganglia-monitor
systemctl status ganglia-monitor
ps -efw | grep gmond

cd ~root/git/scripts/ganglia
make install
./ganglia-all.perl

install gonodeinfo

yes | apt-get -y install golang
mkdir ~/git
cd ~/git
git clone https://bitbucket.org/dd1/gonodeinfo.git
cd gonodeinfo
git pull
make
make install # install gonodeinfo agent
cd ~ # this is important
  • edit /etc/gonodeinfo.conf
  • change "Description", "Location", "User" and "Administrator" as appropriate (or delete them)
  • change "Servers" to read: Servers: ladd00.triumf.ca:8601
  • run gonodeinfo
  • if error is "connection refused". go to the nodeinfo server to add this client to the access control list:
  • on the gonodeinfo server: run gonodereceive -a daq13
  • try gonodeinfo again, there should be no error
  • on the gonodeinfo server: run gonodereport, look at the web pages, the new machine should be listed now

install libz.so.1 for CentOS compatibility

yes | apt-get -y install zlib1g
yes | apt-get -y install zlib1g:i386 libc6:i386 libgcc1:i386 gcc-6-base:i386

install libpng12.so.0 for Quartus compatibility

(does not work anymore!!!) 

wget http://ftp.ca.debian.org/debian/pool/main/libp/libpng/libpng12-0_1.2.50-2+deb8u2_amd64.deb
dpkg --install libpng12-0_1.2.50-2+deb8u2_amd64.deb

install packages for building ROOT

apt-get -y install libx11-dev libxpm-dev libxft-dev libxext-dev libpng-dev libjpeg-dev xlibmesa-glu-dev libxml2-dev libgsl-dev cmake

install 32-bit libraries for PHYSICA

these instructions are for running 32-bit physica executable built for SL6 on ubuntu LTS 20.04

install physica sources (cannot build, do not have g77) 

cd ~/packages
git clone https://bitbucket.org/ttriumfdaq/physica.git

install 32-bit libraries using ubuntu package manager: 

apt install lib32z1 # libz.so

copy 32-bit SL6 shared libraries to /lib32 

root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libX11.so.6 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libgd.so.2 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libpng12.so.0 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libreadline.so.6 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libncurses.so.5 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libg2c.so.0 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libxcb.so.1 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libXpm.so.4 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libjpeg.so.62 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libfontconfig.so.1 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libfreetype.so.6 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libtinfo.so.5 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libXau.so.6 /lib32/
root@trinatdaq:~# cp /daq/daqstore/olchansk/daq/physica-SL6/libexpat.so.1 /lib32/

ldd should report: 

trinatdaq:trinat> ldd /usr/local/physica/physica.exe
	linux-gate.so.1 (0xf7fa2000)
	libX11.so.6 => /lib32/libX11.so.6 (0xf7e43000)
	libgd.so.2 => /lib32/libgd.so.2 (0xf7dfe000)
	libpng12.so.0 => /lib32/libpng12.so.0 (0xf7dd6000)
	libz.so.1 => /lib32/libz.so.1 (0xf7db8000)
	libreadline.so.6 => /lib32/libreadline.so.6 (0xf7d7e000)
	libncurses.so.5 => /lib32/libncurses.so.5 (0xf7d5b000)
	libg2c.so.0 => /lib32/libg2c.so.0 (0xf7d3d000)
	libm.so.6 => /lib32/libm.so.6 (0xf7c39000)
	libgcc_s.so.1 => /lib32/libgcc_s.so.1 (0xf7c1a000)
	libc.so.6 => /lib32/libc.so.6 (0xf7a2f000)
	libxcb.so.1 => /lib32/libxcb.so.1 (0xf7a05000)
	libdl.so.2 => /lib32/libdl.so.2 (0xf79ff000)
	libXpm.so.4 => /lib32/libXpm.so.4 (0xf79ee000)
	libjpeg.so.62 => /lib32/libjpeg.so.62 (0xf7997000)
	libfontconfig.so.1 => /lib32/libfontconfig.so.1 (0xf7962000)
	libfreetype.so.6 => /lib32/libfreetype.so.6 (0xf78c9000)
	libtinfo.so.5 => /lib32/libtinfo.so.5 (0xf78b0000)
	/lib/ld-linux.so.2 (0xf7fa4000)
	libXau.so.6 => /lib32/libXau.so.6 (0xf78ad000)
	libexpat.so.1 => /lib32/libexpat.so.1 (0xf7885000)
trinatdaq:trinat>

set login environment: 

setenv TRIUMF_FONTS $HOME/packages/physica/fonts
setenv PHYSICA_DIR $HOME/packages/physica
alias physica $PHYSICA_DIR/physica-SL6-32

test: 

cd ~/packages/physica
physica
@rangauss.pcm

install desktop environments

note: if apt asks to choose the display manager, select "lightdm" 

# install MATE desktop
yes | apt-get -y install ubuntu-mate-core ubuntu-mate-desktop ubuntu-mate-themes
# install Cinnamon desktop
yes | apt-get -y install cinnamon
# install KDE desktop
yes | apt-get -y install kubuntu-desktop
# install Lxqt desktop
yes | apt-get -y install lxqt
# install Xfce4 desktop
yes | apt-get -y install xfce4

install ROOT

Please install ROOT per instructions at http://root.cern.ch.

NOTE1: The ROOT package available from Ubuntu repositories is severely out of date and cannot be used with MIDAS and ROOTANA. ### DO NOT DO THIS! apt-get install root-system

NOTE2: as of 2017-Jan-09, ROOT binary kits for Ubuntu do not work (use GCC 5 instead of GCC6), build from source instead.

Install x2go

x2go instructions, thanks to Art O. 

add-apt-repository ppa:x2go/stable
apt-get update
apt-get install x2goserver x2goserver-xsession

Post installation

  • setup hostname
xemacs -nw /etc/hostname ### add .triumf.ca to the hostname if it is missing
  • install Konstantin's scripts
mkdir ~root/git
cd ~root/git
git clone https://daq00.triumf.ca/~olchansk/git/scripts.git
cd scripts
git pull
  • enable root login from ladd00/daq00
ssh localhost
CTRL-C
/bin/cp ~root/git/scripts/etc/authorized_keys ~root/.ssh/
  • install smart-status
ln -s ~/git/scripts/smart-status/smart-status.perl .
  • install ganglia additional data
cd ~/git/scripts/ganglia
make

Enable automatic updates

  • apt install unattended-upgrades
  • edit /etc/apt/apt.conf.d/50unattended-upgrades
    • uncomment in Allowed-Origins "-security" and "-updates"
    • add in Allowed-Origins: "Google LLC:stable";
    • uncomment/add: "Unattended-Upgrade::Mail "root";
  • edit/add: /etc/apt/apt.conf.d/10periodic
APT::Periodic::Update-Package-Lists "1";
APT::Periodic::Download-Upgradeable-Packages "1";
APT::Periodic::AutocleanInterval "7";
APT::Periodic::Unattended-Upgrade "1";
  • test: unattended-upgrade --dry-run -v

IPMI instructions

IPMI is the board management hardware on Supermicro and other server motherboards. This includes hardware sensors - fan rotation speed, temperatures and power supply voltages. 

apt-get install ipmitool
systemctl enable ipmievd
systemctl restart ipmievd

Run:

  • ipmitool sel list ### event list
  • ipmitool sel elist ### event list
  • ipmitool sel clear ### clear event list (if it becomes full)
  • ipmitool sensor ### report hardware sensors

NIS instructions (debian 11)

apt -y install rpcbind nis
echo DAQ-NIS >> /etc/defaultdomain
echo ypserver daq00.triumf.ca >> /etc/yp.conf
systemctl enable ypbind.service
systemctl restart ypbind.service
systemctl status ypbind.service
ypwhich -m

then as below:

NIS instructions

  • apt-get -y install portmap nis ### will ask for NIS domain (DAQ-NIS)
  • dpkg-reconfigure nis ### reconfigure if already installed
  • ypwhich -m
  • edit /etc/default/nis
    • set "NISSERVER=slave"
    • set "YPSERVARGS=-p800"
    • Ubuntu LTS 20.04, check that "YPBINDARGS=" is blank, remove "-no-dbus" if it is there
  • edit /etc/yp.conf, comment-out everything, add "domain DAQ-NIS server localhost"
  • /usr/lib/yp/ypinit -s daq00
  • systemctl enable nis
  • systemctl restart nis
  • ypwhich -m
  • ypcat -k passwd
  • apt-get -y install autofs
  • systemctl enable autofs
  • vi /etc/nsswitch.conf ### add the automount line, modify the passwd, group and shadow lines to read this:
# begin get data from nis
passwd: files nis
group: files nis
shadow: files nis
automount:  files nis
netgroup: files nis
# end get data from nis
  • systemctl restart autofs
  • enable hourly update of NIS maps
cd ~/git/scripts/etc
git pull
ln -s $PWD/ypxfr-cron-hourly /etc/cron.hourly
  • ### NOT NEEDED sudo vi /etc/idmapd.conf ### add line: "Domain = triumf.ca"
  • reboot

Fix systemd NIS breakage

!!! THIS IS NOT NEEDED FOR UBUNTU LTS 20.04 !!!

there is a delay in ssh logins for normal users. "ssh -v" shows the delay is after "pledge...". this fix removes the delay.

systemd developers think that we should not use NIS and made sure there are problems if we do. To give them credit, they do offer a workaround. Read this: https://github.com/poettering/systemd/commit/695fe4078f0df6564a1be1c4a6a9e8a640d23b67 

mkdir /etc/systemd/system/systemd-logind.service.d
echo -e "[Service]\nIPAddressDeny=\n" > /etc/systemd/system/systemd-logind.service.d/local.conf
systemctl daemon-reload
systemctl cat systemd-logind.service

Configure lightdm display manager

  • enable it
systemctl disable gdm
systemctl disable sddm
systemctl enable lightdm
  • make the MATE desktop as default
cd ~root/git/scripts/
git pull
/bin/cp -v etc/lightdm_default_mate.conf /etc/lightdm/lightdm.conf.d/
  • enable login by NIS users
/bin/cp -v etc/lightdm_enable_nis_login.conf /etc/lightdm/lightdm.conf.d/
  • restart lightdm
systemctl restart lightdm

Install libpng12.so.0

Quartus 16 needs libpng12: 

wget http://mirrors.kernel.org/ubuntu/pool/main/libp/libpng/libpng12-0_1.2.54-1ubuntu1_amd64.deb
dpkg --install libpng12-0_1.2.54-1ubuntu1_amd64.deb

Install google-chrome

Instructions from here: https://www.ubuntuupdates.org/ppa/google_chrome?dist=stable 

wget -q -O - https://dl-ssl.google.com/linux/linux_signing_key.pub | apt-key add -
sh -c 'echo "deb [arch=amd64] http://dl.google.com/linux/chrome/deb/ stable main" >> /etc/apt/sources.list.d/google.list'
apt update
apt install google-chrome-stable
/bin/rm -f /etc/apt/sources.list.d/google.list

Install amanda client

  • apt install amanda-client
  • edit /etc/amandahosts
amanda.triumf.ca amanda amdump
  • check permissions on /etc/amandahosts:
root@daq00:/var/log/amanda# ls -l /etc/amandahosts
-rw------- 1 backup backup 49 Jan 27 10:48 /etc/amandahosts
  • fix if needed: chown backup.backup /etc/amandahosts; chmod a= /etc/amandahosts; chmod u=wr /etc/amandahosts
  • edit /etc/amanda-security.conf, add this line:
runtar:gnutar_path=/usr/bin/tar

On the amanda machine:

  • in amanda disklist, use dump type "bsdtcp-comp-user-tar"
  • su - amanda and run amcheck -c daq00
-bash-4.1$ amcheck -c daily daq00

Amanda Backup Client Hosts Check
--------------------------------
Client check: 1 host checked in 0.092 seconds.  0 problems found.

(brought to you by Amanda 3.3.7p1.git.685ff76d)

Enable rc.local

For reasons unknown, Ubuntu LTS 20.04 does not enable /etc/rc.local. Do this:

  • create /etc/rc.local with this content
#!/bin/bash

exit 0
  • chmod a+rx /etc/rc.local
  • create systemd service file /etc/systemd/system/rc-local.service
[Unit]
Description=/etc/rc.local Support
ConditionPathExists=/etc/rc.local
After=network.target nis.service autofs.service

[Service]
Type=forking
ExecStart=/etc/rc.local start
TimeoutSec=0
StandardOutput=tty
RemainAfterExit=yes

[Install]
WantedBy=multi-user.target
  • systemctl daemon-reload
  • systemctl enable rc-local
  • systemctl start rc-local
  • systemctl status rc-local

Disable unwanted services

systemctl disable mpd
systemctl disable snapd
systemctl disable ModemManager

Disable sleep and suspend

systemctl mask sleep.target suspend.target hibernate.target hybrid-sleep.target systemd-suspend.service systemd-hybrid-sleep.service

Enable crontab @reboot for MIDAS

startup scripts have a bug - cron @reboot entries for normal users can run before autofs is ready, so if the home directory is on autofs/NFS, it cannot be accessed and the cron job fails. If MIDAS is supposed to be started by cron @reboot, it will not start (there *will* be an error message in /var/log/cron). 

mkdir /etc/systemd/system/cron.service.d
echo -e "[Unit]\nAfter=ypbind.service autofs.service\n" > /etc/systemd/system/cron.service.d/local.conf
systemctl daemon-reload
systemctl cat cron.service

Explore the systemd dependency tree using "systemctl list-dependencies" maybe with "--all".

Visualize the exact boot sequence from previous boot: "systemd-analyze plot > xxx.svg", look at the svg file using a web browser.

Crontab entry to start midas: (install in the midas user crontab, not root crontab) 

su - midasuser
crontab -l
#@reboot /bin/bash -l -c "/home/trinat/bin/start-daq-applications"
#@reboot /bin/tcsh -c "/home/trinat/bin/start-daq-applications"

Install apache httpd proxy for midas and elog

This will configure the HTTPS/SSL certificate using "certbot" and "letsencrypt" and configure an HTTPS web server using apache2.

First, configure apache2:

  • execute these commands:
apt install apache2
cd /etc/apache2
  • create new file conf-available/ssl-daq14.conf # use actual hostname instead of daq14
SSLSessionCache         shmcb:/run/httpd/sslcache(512000)
SSLSessionCacheTimeout  300
SSLRandomSeed startup file:/dev/urandom  256
SSLRandomSeed connect builtin
SSLCryptoDevice builtin
  • create new file sites-available/daq14-ssl.conf # use actual hostname instead of daq14
<IfModule mod_ssl.c>
    <VirtualHost *:443>
        ServerName daq14.triumf.ca
        DocumentRoot /var/www/html
        ErrorLog /var/log/apache2/daq14.log
        SSLEngine on
        # note SSLProtocol, SSLCipherSuite and some other settings are overwritten by /etc/letsencrypt/options-ssl-apache.conf
        SSLProtocol all -SSLv2 -SSLv3 -TLSv1 -TLSv1.1
        SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5:!SEED:!IDEA:!RC4
        ## use port specified in elogd.cfg
        #ProxyPass /elog/ http://localhost:8082/ retry=1 
        ## use mhttpd port
        #ProxyPass /      http://localhost:8080/ retry=1 
        Header always set Strict-Transport-Security "max-age=31536000; includeSubDomains"
        <Location />
            SSLRequireSSL
            AuthType Basic
            AuthName "DAQ password protected site"
            Require valid-user
            # create password file: touch /etc/apache2/htpasswd
            # to add new user or change password: htpasswd /etc/apache2/htpasswd username
            AuthUserFile /etc/apache2/htpasswd
        </Location>
    </VirtualHost>
</IfModule>
  • stop apache2 from listening on port 80: edit /etc/apache2/ports.conf, comment-out the line "Listen 80"
  • stop apache2 from listening on port 80: edit /etc/apache2/ports.conf, comment-out the line "Listen 80"
  • enable ssl module
  • enable new configurations
a2enmod ssl
a2enmod headers
a2enmod proxy
a2enmod proxy_http
a2enconf ssl-daq14
a2ensite daq14-ssl
  • disable default ssl sites
a2dissite 000-default-le-ssl
a2dissite 000-default
ls -l /etc/apache2/sites-enabled/ ### should show only daq14-ssl.conf
  • check that there are no syntax problems
apache2ctl configtest
  • enable and start apache2:
systemctl enable apache2
systemctl restart apache2
systemctl status apache2
  • apache2 may fail to start, look in /var/log/apache2/error.log and /var/log/apache2/daq14.log
  • if it says "Failed to configure ... certificate", proceed to the step for setting certbot.
  • try to access https://daq14.triumf.ca
    • you should see a complaint about self-signed certificate
    • you should see a request for password (do not login yet)
    • if you get "connection refused", HTTPS port 443 may need to be enabled in the local firewall, look at documentation for ufw.

Second, configure certbot:

(Note: as of 2018-01-18 certbot requires use of http port 80 to get the initial https certificate, renewal can continue to use the https port 443)

(Note: as of 2019-01-?? certbot requires use of port 80 for renewals)

  • check that port 80 is not used by anything:
  • netstat -an | grep LISTEN | grep ^tcp | grep 80
  • lsof -P | grep -i tcp | grep LISTEN | grep 80
  • if lsof reports that apache2 is listening on port 80, follow the apache2 instructions above (remove "listen 80" from apache2.conf
  • install certbot (if necessary open tcp port 80 in the firewall, see documentation for ufw):
apt install certbot python3-certbot-apache
certbot certonly --standalone --installer apache
  • then answer questions:
  • "activate HTTPS for daq14.triumf.ca" - say ok
  • "enter email address" - enter your own email address
  • "please read terms..." - read the terms and say "agree"
  • it will take a few moments...
  • "congratulations..." - say ok.
certbot install --apache --cert-name daq14.triumf.ca
  • then answer questions:
  • "choose redirect..." - say "1" (no redirect)
  • look inside /etc/apache2/sites-enabled/ssl-daq14.conf to see that SSLCertificateFile & co point to certbot certificates in

/etc/letsencrypt/live/daq14.triumf.ca/

  • to check current renewal and to update the certbot config file in /etc/letsencrypt/renewal, run this:
certbot renew --standalone --installer apache --force-renewal

NOTE: this certificate will expire in 3 months, automatic renewal should work with current version of certbot

Third, activate password protection:

  • as shown in the config file above, create password file and initial user: (replace "midas" with specific username)
touch /etc/apache2/htpasswd
htpasswd /etc/apache2/htpasswd midas
  • restart apache2
systemctl restart apache2
systemctl status apache2

From here:

  • enable proxy for MIDAS mhttpd - uncomment redirect in the config file above
  • enable proxy for ELOG - ditto
a2enmod proxy
a2enmod proxy_http
apache2ctl configtest
systemctl restart apache2

From here:

  • enable proxy for MIDAS mhttpd - uncomment redirect in the config file above
  • enable proxy for ELOG - ditto
a2enmod proxy
a2enmod proxy_http
apache2ctl configtest
systemctl restart apache2

SSL                  = 0

NOTE: if certbot fails with errors about 'module' object has no attribute 'pyopenssl', try this: pip install requests==2.6.0

Install PHP

  • apt install php libapache2-mod-php
  • systemctl restart apache2
  • create /var/www/html/info.php
<?php 
 
phpinfo();

Update packages

  • apt-get update # update package list
  • apt-get dist-upgrade # install updated packages and update "kept back" packages
  • apt-get autoremove # remove packages that apt thinks should be removed

Finish installation

  • reboot
shutdown -r now

Install ZFS

!!! after installing all the packages, after updating the system, after updating the linux kernel, after rebooting into latest kernel !!! 

apt-get install zfsutils-linux

Follow generic ZFS instructions: ZFS

Update to new version of Ubuntu

vi /etc/update-manager/release-upgrades # set "Prompt=normal"
do-release-upgrade

Ubuntu package manager

  • apt-get install xxx # install package xxx
  • apt-get update
  • apt-get upgrade
  • apt-get dist-upgrade
  • apt-get autoremove # remove automatically installed packages required by a removed package
  • apt-get remove xxx # remove package xxx
  • apt-cache search . # list all available packages
  • apt-cache show "." | grep ^Package # list al available packages
  • apt-cache madison root-system # show all available versions of package root-system
  • apt list # list all installed packages
  • dpkg --listfiles libpng16-16 # list all files from this package
  • apt list --installed # list all installed packages
  • dpkg -S /bin/bash # what package provides this file?
  • dpkg -L bash # what files provided by this package?

Ubuntu boot loader

GRUB

This will enable the grub menu (with a 10 sec timeout) and replace black screen with exciting linux boot messages.

  • edit /etc/default/grub
GRUB_DEFAULT=0
#GRUB_TIMEOUT_STYLE=hidden
GRUB_TIMEOUT=10
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
#GRUB_CMDLINE_LINUX_DEFAULT="vga=769 video=640x480"
GRUB_CMDLINE_LINUX=""
#GRUB_GFXMODE=640x480
  • update grub config:
grub-mkconfig -o /boot/grub/grub.cfg

boot from ZFS

root@daq00:~# zfs list
NAME                                               USED  AVAIL     REFER  MOUNTPOINT
rpool                                              147G  1.62T       96K  /
rpool/ROOT                                        17.8G  1.62T       96K  none
rpool/ROOT/ubuntu_00aaaa                          17.8G  1.62T     6.22G  /
  • copy OS image to rpool/ROOT/ubuntu_00aaaa
  • zfs set mountpoint=/ rpool
  • zfs set mountpoint=none rpool/ROOT
  • zfs set mountpoint=/ rpool/ROOT/ubuntu_00aaaa
  • zfs get all | grep mountpoint
rpool                     mountpoint            /                      local
rpool/ROOT                mountpoint            none                   local
rpool/ROOT/ubuntu_00aaaa  mountpoint            /                      local
  • in linux kernel command line (syslinux.cfg), set "root=" to "root=ZFS=rpool/ROOT/ubuntu_00aaaa"

boot from ZFS mirror

setup the EFI partitions

  • assuming /dev/sdb is already setup for EFI boot, setup /dev/sda the same way:
  • partition the second boot disk same as first boot disk:
root@grsnis01:~# gdisk -l /dev/sdb
Found valid GPT with protective MBR; using GPT.
Number  Start (sector)    End (sector)  Size       Code  Name
   1            2048         1050623   512.0 MiB   EF00  EFI system partition
   2         1050624      3907029134   1.8 TiB     8300  Linux filesystem
root@grsnis01:~#
  • mkfs.msdos /dev/sdX1
  • create mount points
mkdir /boot/efi-sda
mkdir /boot/efi-sdb
  • add to /etc/fstab
/dev/sda1 /boot/efi-sda       vfat    umask=0022,fmask=0022,dmask=0022,nofail      0       1 
/dev/sdb1 /boot/efi-sdb       vfat    umask=0022,fmask=0022,dmask=0022,nofail      0       1
  • mount -a
  • df | grep boot
root@grsnis01:~# df | grep boot
/dev/sdb1                    523248    98100     425148  19% /boot/efi-sdb
/dev/sda1                    523248        4     523244   1% /boot/efi-sda
  • copy boot files to new boot disk
  • cd /boot/efi-sdX; rsync -av . /boot/efi-sdY
  • set BIOS to boot from "UEFI Hard drive", disable legacy boot (except for booting from USB key in legacy mode)
  • if using UEFI boot syslinux per these instructions, linux kernel update has to be done manually by running the script update_efi_mirror.perl (provided by K.O.), follow instructions that it prints.

zetup zfs mirror

root@grsnis01:~# ls -l /dev/disk/by-id/ata*part2
lrwxrwxrwx 1 root root 10 Feb 19 16:47 /dev/disk/by-id/ata-WDC_WDS200T2B0A-00SM50_205007801081-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 Feb 19 16:47 /dev/disk/by-id/ata-WDC_WDS200T2B0A-00SM50_205007801101-part2 -> ../../sdb2

root@grsnis01:~# zpool status
  pool: rpool
 state: ONLINE
  scan: none requested
config:

        NAME                                             STATE     READ WRITE CKSUM
        rpool                                            ONLINE       0     0     0
          ata-WDC_WDS200T2B0A-00SM50_205007801101-part2  ONLINE       0     0     0

errors: No known data errors

root@grsnis01:~# zpool attach rpool ata-WDC_WDS200T2B0A-00SM50_205007801101-part2 /dev/disk/by-id/ata-WDC_WDS200T2B0A-00SM50_205007801081-part2

root@grsnis01:~# zpool status
  pool: rpool
 state: ONLINE
status: One or more devices is currently being resilvered.  The pool will
        continue to function, possibly in a degraded state.
action: Wait for the resilver to complete.
  scan: resilver in progress since Fri Feb 19 16:54:39 2021
        12.6G scanned at 3.16G/s, 1.02G issued at 262M/s, 12.6G total
        1.02G resilvered, 8.09% done, 0 days 00:00:45 to go
config:

        NAME                                               STATE     READ WRITE CKSUM
        rpool                                              ONLINE       0     0     0
          mirror-0                                         ONLINE       0     0     0
            ata-WDC_WDS200T2B0A-00SM50_205007801101-part2  ONLINE       0     0     0
            ata-WDC_WDS200T2B0A-00SM50_205007801081-part2  ONLINE       0     0     0  (resilvering)

errors: No known data errors
  • wait
root@grsnis01:~# zpool status
  pool: rpool
 state: ONLINE
  scan: resilvered 12.7G in 0 days 00:00:40 with 0 errors on Fri Feb 19 16:55:19 2021
config:

        NAME                                               STATE     READ WRITE CKSUM
        rpool                                              ONLINE       0     0     0
          mirror-0                                         ONLINE       0     0     0
            ata-WDC_WDS200T2B0A-00SM50_205007801101-part2  ONLINE       0     0     0
            ata-WDC_WDS200T2B0A-00SM50_205007801081-part2  ONLINE       0     0     0

errors: No known data errors

maintenance commands

  • update-initramfs -v -u
  • grub-install /dev/sda

Disable NetworkManager

NetworkManager is useful for configuring dynamic network interfaces, i.e. laptops that often move between networks, or connect to multiple choice of wifi networks, etc.

For machines with statically configured network interfaces, NetworkManager is not necessary.

As it has been observed to become confused and observed to malfunction when network links go up and down (it keeps unnecessarily reconfiguring the ip address, etc), it can be usefuil to disable it.

  • list all network interfaces
# /bin/ls -1 /sys/class/net/
enp0s31f6
lo
  • edit /etc/network/interfaces:
rename enp0s31f6=eth0
auto eth0
iface eth0 inet static
   address 142.90.120.94/22
   gateway 142.90.100.18
  • statically configure systemd-resolved
xemacs -nw /etc/systemd/resolved.conf ### to read this:
XXX
[Resolve] 
DNS=142.90.100.19
Domains=triumf.ca
XXX
systemctl restart systemd-resolved
resolvectl
  • disable NetworkManager
systemctl disable NetworkManager
  • reboot

Configure ECC memory

Configure EDAC

  • apt install edac-utils

Intel E-2236

root@daq00:~# edac-ctl --mainboard
edac-ctl: mainboard: Supermicro X11SCM-F
root@daq00:~# edac-ctl --status
edac-ctl: drivers are loaded.
root@daq00:~# edac-util 
edac-util: No errors to report.
root@daq00:~# edac-util -s
edac-util: EDAC drivers are loaded. 1 MC detected
  • check edac sysfs files (Intel)
root@daq00:~# ls -l /sys/devices/system/edac/mc/mc0
total 0
-r--r--r-- 1 root root 4096 Jan 25 15:10 ce_count
-r--r--r-- 1 root root 4096 Jan 25 15:10 ce_noinfo_count
-r--r--r-- 1 root root 4096 Jan 25 15:10 max_location
-r--r--r-- 1 root root 4096 Jan 25 15:10 mc_name
drwxr-xr-x 2 root root    0 Jan 25 15:10 power
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank0
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank1
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank2
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank3
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank4
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank5
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank6
drwxr-xr-x 3 root root    0 Jan 25 15:10 rank7
--w------- 1 root root 4096 Jan 25 15:10 reset_counters
-r--r--r-- 1 root root 4096 Jan 25 15:10 seconds_since_reset
-r--r--r-- 1 root root 4096 Jan 25 15:10 size_mb
-r--r--r-- 1 root root 4096 Jan 25 15:10 ue_count
-r--r--r-- 1 root root 4096 Jan 25 15:10 ue_noinfo_count
-rw-r--r-- 1 root root 4096 Jan 25 15:10 uevent
root@daq00:~#

Intel E3-1270 v6

root@wheel-SYS-5019S-M:~/git/scripts# edac-ctl --mainboard
edac-ctl: mainboard: Supermicro X11SSH-F
root@wheel-SYS-5019S-M:~/git/scripts# edac-ctl --status
edac-ctl: drivers are loaded.
root@grsnis01:~# edac-util
edac-util: No errors to report.
root@grsnis01:~# edac-util -s
edac-util: EDAC drivers are loaded. 1 MC detected
root@grsnis01:~# ls -l /sys/devices/system/edac/mc/mc0
total 0
-r--r--r-- 1 root root 4096 Feb 19 12:35 ce_count
-r--r--r-- 1 root root 4096 Feb 19 12:35 ce_noinfo_count
-r--r--r-- 1 root root 4096 Feb 19 12:35 max_location
-r--r--r-- 1 root root 4096 Feb 19 12:35 mc_name
drwxr-xr-x 2 root root    0 Feb 19 12:35 power
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank0
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank1
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank2
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank3
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank4
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank5
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank6
drwxr-xr-x 3 root root    0 Feb 19 12:35 rank7
--w------- 1 root root 4096 Feb 19 12:35 reset_counters
-r--r--r-- 1 root root 4096 Feb 19 12:35 seconds_since_reset
-r--r--r-- 1 root root 4096 Feb 19 12:35 size_mb
-r--r--r-- 1 root root 4096 Feb 19 12:35 ue_count
-r--r--r-- 1 root root 4096 Feb 19 12:35 ue_noinfo_count
-rw-r--r-- 1 root root 4096 Feb 19 12:35 uevent
root@grsnis01:~#

AMD 3700X

(memory is non-ECC) 

root@daq13:~# edac-ctl --mainboard
edac-ctl: mainboard: ASUSTeK COMPUTER INC. ROG STRIX B550-E GAMING
root@daq13:~# 
root@daq13:~# 
root@daq13:~# edac-ctl --status
edac-ctl: drivers not loaded.
root@daq13:~# edac-util 
edac-util: Error: No memory controller data found.
root@daq13:~# edac-util -s
edac-util: EDAC drivers loaded. No memory controllers found
root@daq13:~# ls -l /sys/devices/system/edac/mc
total 0
drwxr-xr-x 2 root root    0 Jan 25 15:26 power
lrwxrwxrwx 1 root root    0 Jan 21 16:16 subsystem -> ../../../../bus/edac
-rw-r--r-- 1 root root 4096 Jan 21 16:16 uevent

(memory is ECC) 

root@trinatdaq:~# edac-ctl --mainboard
edac-ctl: mainboard: ASUSTeK COMPUTER INC. ROG STRIX B550-E GAMING
root@trinatdaq:~# edac-ctl --status
edac-ctl: drivers are loaded.
root@trinatdaq:~# edac-util 
edac-util: No errors to report.
root@trinatdaq:~# edac-util -s
edac-util: EDAC drivers are loaded. 1 MC detected
root@trinatdaq:~# ls -l /sys/devices/system/edac/mc
total 0
drwxr-xr-x 7 root root    0 Dec 15 13:04 mc0
drwxr-xr-x 2 root root    0 Dec 15 13:04 power
lrwxrwxrwx 1 root root    0 Dec 13 18:31 subsystem -> ../../../../bus/edac
-rw-r--r-- 1 root root 4096 Dec 13 18:31 uevent
root@trinatdaq:~# ls -l /sys/devices/system/edac/mc/mc0
total 0
-r--r--r-- 1 root root 4096 Dec 15 13:04 ce_count
-r--r--r-- 1 root root 4096 Dec 15 13:04 ce_noinfo_count
-r--r--r-- 1 root root 4096 Dec 15 13:04 max_location
-r--r--r-- 1 root root 4096 Dec 15 13:04 mc_name
drwxr-xr-x 2 root root    0 Dec 15 13:04 power
drwxr-xr-x 3 root root    0 Dec 15 13:04 rank4
drwxr-xr-x 3 root root    0 Dec 15 13:04 rank5
drwxr-xr-x 3 root root    0 Dec 15 13:04 rank6
drwxr-xr-x 3 root root    0 Dec 15 13:04 rank7
--w------- 1 root root 4096 Dec 15 13:04 reset_counters
-rw-r--r-- 1 root root 4096 Dec 15 13:04 sdram_scrub_rate
-r--r--r-- 1 root root 4096 Dec 15 13:04 seconds_since_reset
-r--r--r-- 1 root root 4096 Dec 15 13:04 size_mb
-r--r--r-- 1 root root 4096 Dec 15 13:04 ue_count
-r--r--r-- 1 root root 4096 Dec 15 13:04 ue_noinfo_count
-rw-r--r-- 1 root root 4096 Dec 15 13:04 uevent
root@trinatdaq:~#

AMD 5000G

  • no linux driver for AMD 5000-series "G" CPU
  • no mention of ECC in the BIOS settings
  • unclear status of ECC support in AMD documentation (sais only "pro" "G" CPUs have ECC)
  • unclear status of ECC support in ASUS documentation (web page out of date)

Configure rasdaemon

  • apt install rasdaemon
  • systemctl enable rasdaemon
  • systemctl start rasdaemon
  • systemctl status rasdaemon
● rasdaemon.service - RAS daemon to log the RAS events
     Loaded: loaded (/lib/systemd/system/rasdaemon.service; enabled; vendor preset: enabled)
     Active: active (running) since Mon 2021-01-25 15:16:37 PST; 3min 5s ago
   Main PID: 2477175 (rasdaemon)
      Tasks: 1 (limit: 76958)
     Memory: 17.1M
     CGroup: /system.slice/rasdaemon.service
             └─2477175 /usr/sbin/rasdaemon -f -r

Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: ras:extlog_mem_event event enabled
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: Enabled event ras:extlog_mem_event
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: ras:extlog_mem_event event enabled
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: Listening to events for cpus 0 to 11
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: Enabled event ras:extlog_mem_event
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: Recording mc_event events
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: Recording aer_event events
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: Recording extlog_event events
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: Recording mce_record events
Jan 25 15:16:37 daq00.triumf.ca rasdaemon[2477175]: rasdaemon: Recording arm_event events

Get reports

  • Intel 2x32GB ECC DIMMs
root@daq00:~# ras-mc-ctl --layout
          +-------------------------+
          |           mc0           |
          |   csrow0   |   csrow1   |
----------+-------------------------+
channel1: |  16384 MB  |  16384 MB  |
channel0: |  16384 MB  |  16384 MB  |
----------+-------------------------+
root@daq00:~# ras-mc-ctl --error-count
Label                   CE      UE
mc#0csrow#1channel#1    0       0
mc#0csrow#1channel#0    0       0
mc#0csrow#0channel#0    0       0
mc#0csrow#0channel#1    0       0
root@daq00:~#
  • Intel 4x16GB ECC DIMMs
root@daq00:~# ras-mc-ctl --error-count
Label                   CE      UE
mc#0csrow#0channel#1    0       0
mc#0csrow#2channel#0    0       0
mc#0csrow#0channel#0    0       0
mc#0csrow#2channel#1    0       0
mc#0csrow#1channel#0    0       0
mc#0csrow#1channel#1    0       0
mc#0csrow#3channel#0    0       0
mc#0csrow#3channel#1    0       0
root@daq00:~# 
root@daq00:~# ras-mc-ctl --layout
          +-----------------------+
          |          mc0          |
          |  csrow0   |  csrow1   |
----------+-----------------------+
channel1: |  8192 MB  |  8192 MB  |
channel0: |  8192 MB  |  8192 MB  |
----------+-----------------------+
root@daq00:~# 
root@daq00:~# 
root@daq00:~# 
root@daq00:~# ras-mc-ctl --print-labels
ras-mc-ctl: Error: No dimm labels for Supermicro model X11SCM-F
root@daq00:~# ras-mc-ctl --mainboard
ras-mc-ctl: mainboard: Supermicro model X11SCM-F
root@daq00:~# ras-mc-ctl --summary
No Memory errors.

No PCIe AER errors.

No Extlog errors.

DBD::SQLite::db prepare failed: no such table: devlink_event at /usr/sbin/ras-mc-ctl line 1181.
Can't call method "execute" on an undefined value at /usr/sbin/ras-mc-ctl line 1182.
root@daq00:~#

sensors

ASUS P9X79 WS

root@daq14:~# sensors
coretemp-isa-0000
Adapter: ISA adapter
Package id 0:  +35.0°C  (high = +82.0°C, crit = +100.0°C)
Core 0:        +29.0°C  (high = +82.0°C, crit = +100.0°C)
Core 1:        +24.0°C  (high = +82.0°C, crit = +100.0°C)
Core 2:        +35.0°C  (high = +82.0°C, crit = +100.0°C)
Core 3:        +32.0°C  (high = +82.0°C, crit = +100.0°C)

nouveau-pci-0200
Adapter: PCI adapter
GPU core:    900.00 mV (min =  +0.85 V, max =  +1.00 V)
temp1:        +39.0°C  (high = +95.0°C, hyst =  +3.0°C)
                       (crit = +105.0°C, hyst =  +5.0°C)
                       (emerg = +135.0°C, hyst =  +5.0°C)

nct6776-isa-0290
Adapter: ISA adapter
Vcore:           1.04 V  (min =  +0.00 V, max =  +1.74 V)
in1:             1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
AVCC:            3.33 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
+3.3V:           3.33 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in4:             1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:             2.04 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:           904.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
3VSB:            3.41 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
Vbat:            3.30 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
fan1:          1265 RPM  (min =    0 RPM)
fan2:          1909 RPM  (min =    0 RPM)
fan3:             0 RPM  (min =    0 RPM)
fan4:             0 RPM  (min =    0 RPM)
fan5:             0 RPM  (min =    0 RPM)
SYSTIN:         +34.0°C  (high =  +0.0°C, hyst =  +0.0°C)  ALARM  sensor = thermistor
CPUTIN:         +58.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermal diode
AUXTIN:         +31.5°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermistor
PECI Agent 0:   +31.0°C  (high = +80.0°C, hyst = +75.0°C)
                         (crit = +96.0°C)
PCH_CHIP_TEMP:   +0.0°C  
PCH_CPU_TEMP:    +0.0°C  
PCH_MCH_TEMP:    +0.0°C  
intrusion0:    ALARM
intrusion1:    ALARM
beep_enable:   disabled

root@daq14:~#

Enable CPU turbo mode

  • Intel CPU has a nominal CPU frequency (i.e. 3.4GHz) and a turbo-boost CPU frequency (i.e. 4.0GHz). Here we will enable this turbo-boost mode.
  • Find out CPU capability
root@daq01:~# lscpu | grep Hz
Model name:                      Intel(R) Core(TM) i7-6700 CPU @ 3.40GHz
CPU MHz:                         3965.803
CPU max MHz:                     4000.0000
CPU min MHz:                     800.0000
root@daq01:~#
  • Look up this CPU in the Intel ARK database - google for the CPU model name, i.e.

https://ark.intel.com/content/www/us/en/ark/products/88196/intel-core-i7-6700-processor-8m-cache-up-to-4-00-ghz.html

  • Find current frequency settings:
root@daq01:~# cpupower frequency-info
analyzing CPU 0:
  driver: intel_pstate
  CPUs which run at the same hardware frequency: 0
  CPUs which need to have their frequency coordinated by software: 0
  maximum transition latency:  Cannot determine or is not supported.
  hardware limits: 800 MHz - 4.00 GHz
  available cpufreq governors: performance powersave
  current policy: frequency should be within 800 MHz and 4.00 GHz.
                  The governor "powersave" may decide which speed to use
                  within this range.
  current CPU frequency: Unable to call hardware
  current CPU frequency: 2.72 GHz (asserted by call to kernel)
  boost state support:
    Supported: yes
    Active: yes
root@daq01:~#
  • Note the following:
    • current governor is "powersave"
    • "performance" governor is available
    • "boost state support" is supported and active.
  • Confirm CPU frequency governor:
root@daq01:~# cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
root@daq01:~#
  • Change governor to "performance":
root@daq01:~# cpupower frequency-set --governor performance
Setting cpu: 0
Setting cpu: 1
Setting cpu: 2
Setting cpu: 3
Setting cpu: 4
Setting cpu: 5
Setting cpu: 6
Setting cpu: 7
root@daq01:~# cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
performance
performance
performance
performance
performance
performance
performance
performance
root@daq01:~# cpupower frequency-info
analyzing CPU 0:
  driver: intel_pstate
  CPUs which run at the same hardware frequency: 0
  CPUs which need to have their frequency coordinated by software: 0
  maximum transition latency:  Cannot determine or is not supported.
  hardware limits: 800 MHz - 4.00 GHz
  available cpufreq governors: performance powersave
  current policy: frequency should be within 800 MHz and 4.00 GHz.
                  The governor "performance" may decide which speed to use
                  within this range.
  current CPU frequency: Unable to call hardware
  current CPU frequency: 3.93 GHz (asserted by call to kernel)
  boost state support:
    Supported: yes
    Active: yes
  • monitor CPU frequency:
root@daq01:~# cpupower monitor
    | Nehalem                   || Mperf              || Idle_Stats                                     
 CPU| C3   | C6   | PC3  | PC6   || C0   | Cx   | Freq  || POLL | C1   | C1E  | C3   | C6   | C7s  | C8    
   0|  0.00|  0.00|  0.00|  0.00|| 88.80| 11.20|  3973||  0.00|  0.00|  0.01|  0.02|  0.31|  0.00|  4.25
   4|  0.00|  0.00|  0.00|  0.00||  4.70| 95.30|  3945||  0.00|  0.00|  0.00|  0.00|  0.00|  0.00| 95.03
   1|  0.73|  3.70|  0.00|  0.00||  4.52| 95.48|  3864||  0.00|  0.01|  1.19|  0.44|  2.82|  0.00| 90.23
   5|  0.73|  3.70|  0.00|  0.00||  0.37| 99.63|  3807||  0.00|  0.00|  0.03|  0.09|  1.70|  0.00| 97.64
   2|  2.28| 12.86|  0.00|  0.00||  1.41| 98.59|  3829||  0.00|  0.86|  3.17|  0.46|  7.70|  0.00| 85.87
   6|  2.28| 12.86|  0.00|  0.00||  2.88| 97.12|  3856||  0.00|  0.11|  4.56|  2.15| 10.31|  0.00| 78.99
   3|  1.33|  4.81|  0.00|  0.00||  0.99| 99.01|  3804||  0.00|  0.49|  0.79|  0.01|  1.03|  0.00| 96.12
   7|  1.34|  4.81|  0.00|  0.00||  1.26| 98.74|  3818||  0.00|  0.01|  2.32|  0.47|  5.02|  0.00| 90.06
root@daq01:~#
  • check that the CPU is not overheating:
root@daq01:~# sensors
coretemp-isa-0000
Adapter: ISA adapter
Package id 0:  +51.0°C  (high = +84.0°C, crit = +100.0°C)
Core 0:        +51.0°C  (high = +84.0°C, crit = +100.0°C)
Core 1:        +38.0°C  (high = +84.0°C, crit = +100.0°C)
Core 2:        +34.0°C  (high = +84.0°C, crit = +100.0°C)
Core 3:        +32.0°C  (high = +84.0°C, crit = +100.0°C)
  • congratulations, we are running at 4 GHz now!

Setup ubuntu as gateway to private network

See also:

Steps to do

  • assign network numbers to the private network, i.e. 192.168.1.x, 192.168.2.x, etc
  • (on the gateway machine, each private network interface has to have a different network number)
  • (each network interface can have multiple networks attached, via VLANs or via eth0:0, eth0:1 constructs)
  • assign IP addresses on the private network, save them in /etc/hosts i.e. "hvps 192.168.1.10"
  • (for simplicity, assign 192.168.1.1 to the gateway machine itself)
  • (IP addresses 192.168.1.0 and 192.168.1.255 are "special", do not use them)
  • setup DNS server (dnsmasq) to serve contents of /etc/hosts via DNS (otherwise, many programs will see inconsistent name to IP address mapping)
  • setup DHCP server (ISC dhcpd or dnsmasq) to give out the IP addresses
  • setup tftp, pxelinux and NFS for diskless booting
  • setup time server (chronyd) to provide common time to all devices
  • setup NAT so machines on private network can access the internet (to get OS updates, etc)
  • setup NIS and NFS so machines on the private network can use common home directories
  • setup rsync backup of machines on the private network

setup hosts

  • edit /etc/hosts
192.168.1.101 dsfe01
... and so forth

setup dns and dhcp

  • apt-get install dnsmasq
  • edit /etc/dnsmasq.conf
# /etc/dnsmasq.conf
# DNS settings
#port=0 # disable DNS function
port=53
domain-needed
bogus-priv
no-resolv
server=142.90.100.19
# DHCP settings
interface=enp1s0f0 # DHCP interface
#dhcp-range=192.168.1.50,192.168.1.150,infinite
dhcp-range=192.168.1.0,static
dhcp-boot=pxelinux.0
#dhcp-host=ac:1f:6b:9e:7f:4a,192.168.1.100,10m
dhcp-host=ac:1f:6b:9e:7f:4a,dsfe01,infinite
# TFTP settings
enable-tftp
tftp-root=/zssd/tftpboot
  • mkdir /zssd/tftpboot ### per tftp-root
  • systemctl enable dnsmasq
  • systemctl restart dnsmasq

setup chronyd

  • enable ntp server:
  • configure and enable chronyd per instructions above
  • emacs -nw /etc/chrony/chrony.conf
    • add "allow 192.168.1.0/24" at the end
  • systemctl restart chronyd
  • chronyc tracking ### wait until time is synchronized (a few seconds)

setup diskless network booting

setup pxelinux

cd ~
wget https://www.kernel.org/pub/linux/utils/boot/syslinux/4.xx/syslinux-4.03.tar.bz2
tar xjvf syslinux-4.03.tar.bz2
cd syslinux-4.03
cp -pv ./core/pxelinux.0 ./com32/hdt/hdt.c32 ./memdisk/memdisk ./com32/menu/menu.c32 /zssd/tftpboot/
  • cd /zssd/tftpboot
wget http://ladd00.triumf.ca/tftpboot/memtest86+-4.20.iso.zip
wget http://ladd00.triumf.ca/tftpboot/memtest86+-5.01.iso.gz
wget http://ladd00.triumf.ca/tftpboot/modules.alias
wget http://ladd00.triumf.ca/tftpboot/modules.pcimap
wget http://ladd00.triumf.ca/tftpboot/pci.ids
  • mkdir pxelinux.cfg
  • emacs -nw pxelinux.cfg/default
default menu.c32
prompt 0

menu title Welcome to the DSVSLICE PXE boot menu

timeout 50

label hdt
  kernel hdt.c32

label memtest86+-5.01 
  kernel memdisk iso initrd=memtest86+-5.01.iso.gz 

label memtest86+-4.20
  kernel memdisk iso initrd=memtest86+-4.20.iso.zip

label vmlinuz-5.3.0-26-generic
  menu default
  kernel vmlinuz-5.3.0-26-generic
  append initrd=initrd.img-5.3.0-26-generic boot=nfs root=/dev/nfs netboot=nfs nfsroot=192.168.1.1:/zssd/nfsroot/dsfe01 toram ip=dhcp panic=60 BOOTIF=enp1s0f0

#end

setup linux kernel

  • copy the kernel files
cd /boot
rsync -av config* initrd* System.map* vmlinuz* /zssd/tftpboot/
  • cd /zssd/tftpboot
  • chmod a+r *

setup nfs

  • apt-get install nfs-kernel-server
  • emacs -nw /etc/exports
/zssd/nfsroot/dsfe01 dsfe01(rw,no_root_squash,async,no_subtree_check)
  • enable services
systemctl enable nfs-server
systemctl enable nfs-mountd
systemctl enable nfs-idmapd
systemctl restart nfs-server
systemctl restart nfs-mountd
systemctl restart nfs-idmapd
  • after editing /etc/exports, run
exportfs -av

setup userland

  • zfs create zssd/nfsroot
  • zfs set dedup=verify zssd/nfsroot ### enable deduplication to save disk space because most linux images have mostly identical files
  • clone ubuntu
mkdir /zssd/nfsroot/dsfe01
cd /
rsync -avx . /zssd/nfsroot/dsfe01
  • edit config files:
  • cd /zssd/nfsroot/dsfe01
  • emacs -nw etc/hostname ### change to dsfe01
  • emacs -nw etc/fstab ### add this
192.168.1.1:/zssd/nfsroot/dsfe01 / nfs defaults,nolock 0 0
  • emacs -nw etc/chrony/chrony.conf
    • comment-out all "pool" and "server" entries
    • add entry "server 192.168.1.1 iburst"

After dsfe01 is booted:

  • disable services:
systemctl disable apache2
systemctl disable dnsmasq
systemctl disable zfs-import-cache

To setup additional machines, clone dsfe01 instead of cloning the gateway machine

Allow manpages to be viewed

If / is mounted over NFS, man will report a permission error. Fix it with: 

ln -s /etc/apparmor.d/usr.bin.man /etc/apparmor.d/disable/
apparmor_parser -R /etc/apparmor.d/usr.bin.man

setup shared home directory

on the gateway machine

  • define netgroups
  • emacs -nw /etc/netgroup
dsfe (dsfe01,,) (dsfe02,,)
  • emacs -nw /etc/nsswitch.conf ### edit the netgroup line to read:
netgroup: files
  • export the home directories:
  • emacs -nw /etc/exports ### add this:
/zssd/home1 @dsfe(rw,no_root_squash,async,no_subtree_check)
  • exportfs -rc

on the frontend machine

  • mkdir /home
  • emacs -nw /etc/fstab ### add this:
192.168.1.1:/zssd/home1 /home nfs defaults 0 0
  • mount -a

setup NAT

NAT allows machines on the private network to connect to the internet: https://en.wikipedia.org/wiki/Network_address_translation

In these examples:

  • replace "eno1" with name of the outgoing interface (the one connected to the TRIUMF network).
  • replace "enp11s0" with name of the private network interface (192.168.1.x network)
  • emacs -nw /etc/rc.local ### add this:
# /etc/rc.local

/sbin/iptables -t nat -A POSTROUTING -o eno1 -j MASQUERADE
iptables -L -v

# uncomment following lines if machine has prohibitive FORWARD rules:
#/sbin/iptables -I FORWARD -i eno1 -o enp11s0 -m state --state RELATED,ESTABLISHED -j ACCEPT
#/sbin/iptables -I FORWARD -i enp11s0 -o eno1 -j ACCEPT
#iptables -L -v

iptables -L -v
sysctl -w net.ipv4.ip_forward=1
#sysctl -a | grep forward

sh /etc/firewall-rfc1918.sh

# end
  • emacs -nw /etc/firewall-rfc1918.sh
# firewall-rfc1918.sh

# prevent RFC1918 private network IP addresses from
# going in and out from our uplink.

ETH=eno1

iptables -F in-rfc1918
iptables -N in-rfc1918
iptables -A in-rfc1918 --dst 10.0.0.0/8      -j REJECT
iptables -A in-rfc1918 --dst 172.16.0.0/12   -j REJECT
iptables -A in-rfc1918 --dst 192.168.0.0/16  -j REJECT
iptables -D INPUT -j in-rfc1918 -i $ETH
iptables -D INPUT -j in-rfc1918 -i $ETH
iptables -I INPUT -j in-rfc1918 -i $ETH

iptables -F out-rfc1918
iptables -N out-rfc1918
iptables -A out-rfc1918 --dst 10.0.0.0/8      -j REJECT
iptables -A out-rfc1918 --dst 172.16.0.0/12   -j REJECT
iptables -A out-rfc1918 --dst 192.168.0.0/16  -j REJECT
iptables -D OUTPUT -j out-rfc1918 -o $ETH
iptables -D OUTPUT -j out-rfc1918 -o $ETH
iptables -I OUTPUT -j out-rfc1918 -o $ETH

iptables -L -v

#end
Retrieved from "https://daq00.triumf.ca/DaqWiki/index.php?title=Ubuntu&oldid=4716"