TRB3 Centos-7 instructions: Difference between revisions
| Line 93: | Line 93: | ||
</pre> | </pre> | ||
* | * Start the MIDAS TRB3 readout frontend, if not running: | ||
<pre> | |||
/home/trb3/online/trb3_frontend/fetrb3UDP.exe -D | |||
</pre> | |||
As noted, we currently (April 9) we have the TRB3 setup with a 10kHz software trigger. | |||
== Running the online analyzer == | == Running the online analyzer == | ||
Revision as of 10:55, 9 April 2018
Introduction
See main TRB3 document for introductory material.
Centos-7 Software Setup
The TRB3 software and associated analysis packages are developed on newer operating systems than Centos-7 (namely Opensuse). So a certain amount of work is needed to get the software to work on Centos-7.
1) I started by copying over the software in trbsoft from an existing installation.
scp trbsoft_backup.tar.gz trb3@ladd00:/data0/trb3/.
2) The main problem is with the TRB3 code requiring a newer version of perl. I used perlbrew to setup a newer version of perl than Centos-7 supports:
Following the instructions on website:
source ~/perl5/perlbrew/etc/bashrc perlbrew init perlbrew install perl-5.24.0
and then add this line to login script
rm -f /home/trb3/.perlbrew/init source ~/perl5/perlbrew/etc/bashrc perlbrew switch perl-5.24.0
3) Rebuild libtrbnet with different perl
cd ~/trbsoft/trbnettools/libtrbnet_perl perl Makefile.PL cd /home/trb3/trbsoft/trbnettools make TRB3=1 clean make TRB3=1 make TRB3=1 install <pre> 4) Modify <pre> ~/trbsoft/daqtools/merge_serial_address.pl
to use the perlbrew version of perl, rather than the system default.
5) Rebuild DABC
Make sure you have ROOT (ie ROOTSYS) setup properly
svn co https://subversion.gsi.de/dabc/trb3 trb3 cd trb3 make
This seems to build dabc and stream successfully. go4 doesn't compile cleanly, but this doesn't matter for the MIDAS frontend readout.
TRB3 MIDAS implementation
We have a working MIDAS readout of the TRB3 TDC data. Currently this readout uses a lot of the original GSI tools for setting up the TRB3 before the readout can start. At this time you need to do steps 1 and 2 described in "Start up instructions" in order to setup the TRB3 before starting the MIDAS frontend. Eventually we will try to remove as many as possible of the original GSI tools.
MIDAS frontend code is available here:
https://bitbucket.org/ttriumfdaq/trb3_frontend
The MIDAS frontend is setup to read events directly from the UDP buffer. You can see a running MIDAS TRB3 frontend here:
(midas/midas).
Setting up for MIDAS data taking
We are using the account trb3@daq11.triumf.ca for running this DAQ. If you need to restart the DAQ system, do the following
- Run the setup program that will initialize the TRB3 and set the 10kHz software trigger
cd /home/trb3/trbsoft/daqtools/users/triumf_trb171 source startup.sh
- (Optional) We can also start a webgui that allows us to check/configure the TRB3 separate from MIDAS; this is sometimes useful for monitoring. To do this, do
cd /home/trb3/trbsoft/daqtools/web ./cts_gui --noopenxterm --port=1234 --endpoint=0xc001
- Start the MIDAS TRB3 readout frontend, if not running:
/home/trb3/online/trb3_frontend/fetrb3UDP.exe -D
As noted, we currently (April 9) we have the TRB3 setup with a 10kHz software trigger.
Running the online analyzer
I added simple decoder and histograming classes to rootana. Currently I have only implemented the crude TDC calibration into the TRB3 bank decoders. In the long run we may want to integrate the fine TDC calibration directly into the frontend. You can see the TDC difference between a pulser split into two channels here
Look for the histogram TRB3_diff_0_3.