BNMR: Shift Monitor

• BNMR overview
• Getting started
• Troubleshooting
• All BNMR pages
• Midas

Links

• BNMR
• Experimental Modes
• Getting Started

Introduction

The BNMR shift monitor system consists of two perlscripts in directory /home/bnmr/online/perl :

• monitor.pl
• cycle_monitor_logfiles.pl

both of which are normally run as cron jobs. They are run as user bnmr, and access the required information from both the bnmr and bnqr ODBs.

The Shift Monitor program monitor.pl keeps a running total of how much usable beam time (in minutes) each TRIUMF experimental group has had access to, while running as experiment bnmr or bnqr (or both). It reads the proton current from EPICS once per minute. The information is stored in shift files in the directory /isdaq/data1/bnmr/mon/<year>/. This is also the location of the log files used to store messages.

How it works

The perlscript /home/bnmr/vmic_online/perl/monitor.pl is run on isdaq01 (i.e. the midas host for bnmr and bnqr experiments) as a cron job (except for testing). Its output is written to a log file. It is run as user bnmr, which has permission to access the EPICS variables needed.

The script determines which TRIUMF experimental group is running by reading the experiment number from the ODB parameter /Experiment/Edit on start/experiment number on both experiments. Access to the bnqr ODB is done using odbedit -c

The perlscript monitor.pl reads the proton current from EPICS (via caget "CCS2ISAC:BL2ACURRENT").

• If it is below the threshold value (supplied as the first input parameter to monitor.pl), it exits.
• Otherwise it reads from the EPICS switches which experiment(s) is/are enabled:
  Either
  • bnmr in single channel mode, or
  • bnqr in single channel mode, or
  • both experiments (in dual channel mode)
• It reads the experiment number from the enabled experiment(s). The experiment number must be > 0, otherwise no beam time will be allocated.
• The program determines the name of the shift file by date and by 12-hour shift (AM/PM).
• If no file of that filename exists, it is created and a line written for each different experiment number, and each running experiment assigned 1 minute of running time.
• If bnmr and bnqr are both running with the same experiment number, only one line will be created with bnmr and bnqr experiments each given 1 minute accumulated time.
• If there is an existing file, the program looks for a line with the experiment number. If it finds one, the accumulated time is incremented for the appropriate experiment. All other lines are copied and an updated file is written. If no line exists for this experiment number, a new line will be written.
• If test mode is enabled (see #Input Parameters) an entry to the shift file written in test mode will be followed by an asterisk (see example).

The script cycle_monitor_logfiles.pl cycles the logfiles to save disk space. After 5 days, the logfile information is deleted.

Note

the shift files are never deleted unless by the user.

Log files

The current log file is /isdaq/data1/bnmr/mon/<year>/monitor.log

When running monitor.pl as a cron job, the output of the program can only be found in the log file, since printing to the screen must be suppressed (to prevent excessive email).

Cycling the log files

A second cron job cycle_monitor_logfiles.pl cycles the log files, so that a new monitor.log file is started every 24 hours. Five days worth of logs are retained in files monitor.log_1 to monitor.log_5 where monitor.log_5 is the oldest. Each day the cron job deletes monitor.log_5, renames monitor.log_n to monitor.log_n+1 and renames monitor.log to monitor.log_1. This is done to limit the disk space taken up by the log files.

cycle_monitor_logfiles.pl takes one parameter, which when set to 1 suppresses printing to the screen. Output from cycle_monitor_logfiles.pl can be found in cycle_files.log. A version of this file is created each time the script runs.

Shift files

Shift files are located in the directory /isdaq/data1/bnmr/mon/<year>/ and filenames are of the form

24Jul2014_AM.txt, 24Jul2014_PM.txt. The AM shift starts at 8.30am, the PM shift at 8:30pm.

The format of the shift files is e.g.

# Shift Monitor File first opened at Thu Jul 24 13:52:21 2014
# Threshold(uA)   ExptNum        BNMR(min)       BNQR(min)   Time line written         Testing
  10.000         00001508        0080            0036        Thu Jul 24 15:50:01 2014    *
  10.000         00001412        0035            0021        Thu Jul 24 15:49:02 2014    *

The * under "Testing" indicates test mode (see #How it works).

Input Parameters

Table 1 : Input Parameters to monitor.pl

Input Parameter		Explanation
1	Proton Current Threshold (uA)	User selected value. If proton current is less than this value, program will exit without updating shift file.
2	Suppress printing	Must be TRUE if running as a cron job
3	Test Mode	Set TRUE for testing if EPICS switches are set to "off"
4	BNMR enabled	In Test Mode, set TRUE to enable BNMR regardless of EPICS switch
5	BNQR enabled	In Test Mode, set TRUE to enable BNQR regardless of EPICS switch

Running the program by hand

The perlscript monitor.pl can be run by hand to check its operation. However, each time it is run, a minute will be added to the current experiment(s) in the shift files.

Therefore, it should not be run by hand during the beam period if the cron job is running.

To run the program, as user bnmr, in an xterm type e.g.

/home/bnmr/vmic_online/perl/monitor.pl  15  

Printing to the screen ( input parameter 2) need not be suppressed when running by hand.

The program can also be run in test mode, e.g

/home/bnmr/vmic_online/perl/monitor.pl  0 0 1 0 1  

This would enable the bnqr experiment regardless of the state of the proton current and the EPICS switches (see #Input Parameters).

The program cycle_monitor_logfiles.pl can also be run by hand at any time. Printing messages to the screen will not be suppressed if run as follows:

/home/bnmr/vmic_online/perl/cycle_monitor_logfiles.pl 

Running the cron job

As user bnmr, in an xterm type

$ crontab -l 

to list the crontab file, or to edit it

$ crontab -e

The crontab file will be displayed as follows:

# MAILTO=GM <gmorris@triumf.ca>
SHELL=/bin/csh
# cron parameters :
# minute hour dayofmonth month dayofweek command
#
# cycle_monitor_logfiles.pl : cycle the logfiles monitor.log
#
#: output from this script in cycle_files.log
# run like this as cron job (argument=1 suppresses printing to screen)
30 8,20 * * * /home/bnmr/vmic_online/perl/cycle_monitor_logfiles.pl 1
#
#
# monitor.pl parameters: proton_current(uA) noprint testing bnmr_running bnqr_running
#
# run like this for TESTING cron job when epics switches are not set correctly and proton I is zero:
#
#use the odb to change the experiment numbers under "/experiment/edit on start/"
#* * * * * /home/bnmr/vmic_online/perl/monitor.pl 0 1 1 1 1
#
# run like this normally (change "10" to required proton current threshold) :
# Uncomment to turn on logging
# this editor is emacs: use C-x C-c y to save changes and exit
# typical BL2A current is about 40 \mu A; set a threshold somewhat less.
#
* * * * * /home/bnmr/vmic_online/perl/monitor.pl 35 1

The example above shows

• the script cycle_monitor_logfiles.pl run twice per day (cron parameters are minute=30 hour=8,20 i.e. 8.30am and pm)
• the shift program monitor.pl being run as a cron job every minute (cron parameters all = *) with parameters
  • minimum proton current 10
  • suppress printing TRUE

Printing must be suppressed when running as a cron job, otherwise the MAILTO recipient will get long email messages every minute. If the last line is commented out, the cron job will not be running the monitor program (see stopping the cron job).

Stopping the cron job

As user bnmr, in an xterm type

$ crontab -e

which will display the crontab file to be edited (see above). Comment out the two lines that starts the perlscripts, i.e.

    # ...........
    #30 20 * * * /home/bnmr/vmic_online/perl/cycle_monitor_logfiles.pl 1
    # ...........
    # * * * * * /home/bnmr/vmic_online/perl/monitor.pl 10 1

and exit from the editor.