MityCAMAC: Difference between revisions

From DaqWiki
Jump to navigation Jump to search
Line 142: Line 142:
inhibit        0x0020 |OO| 0x0100
inhibit        0x0020 |OO| 0x0100
-----------------------------------------------------
-----------------------------------------------------
</pre>
== Front Panel LEMO connectors ==
<pre>
AAA
</pre>
</pre>


Revision as of 14:08, 19 January 2015

CriticalLink MityARM

Links

Useful links

minicom settings

    +-----------------------------------------------------------------------+
    | A -    Serial Device      : /dev/ttyUSB0                              |
    | B - Lockfile Location     : /var/lock                                 |
    | C -   Callin Program      :                                           |
    | D -  Callout Program      :                                           |
    | E -    Bps/Par/Bits       : 115200 8N1                                |
    | F - Hardware Flow Control : No                                        |
    | G - Software Flow Control : No                                        |
    |                                                                       |
    |    Change which setting?                                              |
    +-----------------------------------------------------------------------+

 +--------------------[Modem and dialing parameter setup]---------------------+
 |                                                                            |
 | A - Init string .........                                                  |
 | B - Reset string ........                                                  |
 | C - Dialing prefix #1.... ATDT                                             |
 | D - Dialing suffix #1.... ^M                                               |
 | E - Dialing prefix #2.... ATDP                                             |
 | F - Dialing suffix #2.... ^M                                               |
 | G - Dialing prefix #3.... ATX1DT                                           |
 | H - Dialing suffix #3.... ;X4D^M                                           |
 | I - Connect string ...... CONNECT                                          |
 | J - No connect strings .. NO CARRIER            BUSY                       |
 |                           NO DIALTONE           VOICE                      |
 | K - Hang-up string ...... ~~+++~~ATH^M                                     |
 | L - Dial cancel string .. ^M                                               |
 |                                                                            |
 | M - Dial time ........... 45      Q - Auto bps detect ..... No             |
 | N - Delay before redial . 2       R - Modem has DCD line .. Yes            |
 | O - Number of tries ..... 10      S - Status line shows ... DTE speed      |
 | P - DTR drop time (0=no). 1       T - Multi-line untag .... No             |
 |                                                                            |
 | Change which setting?       (Return or Esc to exit)                        |
 +----------------------------------------------------------------------------+

BOOTCONFIG

BOOTCONFIG settings:

  • CL eval board:
    • BOOTCONFIG[0..11] are SYSBOOT[0..11]
    • boot from SD: all open, [3] closed
    • boot from on-SoM NAND: all open, close [2], [3], [8], [9], [10], [11] (6 jumpers)
  • CAMAC board:
    • top-to-bottom: B0..4,G0..5,R0 correspond to LCD_DATA[0..11] are SYSBOOT[0..11]
    • boot from SD: all open, B3 closed
    • boot from on-SoM NAND: all open, close B2, B3, G3, G4, G5, R0 (6 jumpers)

NOTES:

  • boot from EMAC1 requires PHY connection to RGMII1, CLeval and CAMAC boards connected PHY to RGMII2.

SYSBOOT modes: http://ladd00.triumf.ca/~olchansk/MityARM/Docs/spruh73g.pdf table 26-7 

SYSBOOT[4..0]
00000 - reserved
00001 - UART0
00010 - UART0
00011 - UART0
00100 - UART0
00101 - UART0
00110 - EMAC1, SYSBOOT[7..6]: 00=MII, 01=RMII, 10=reserved, 11=RGMII
00111 - EMAC1
01000 - EMAC1
01001 - EMAC1
01010 - EMAC1
01011 - USB0
01100 - USB0
01101 - USB0
01110 - reserved
01111 - fast external boot
10000 - XIP
10001 - XIP
10010 - NAND
10011 - NAND
10100 - NAND
10101 - NAND-I2C
10110 - SPI0
10111 - MMC0 <---- default (boot from SD flash) - other bits - don't care
11000 - SPI0
11001 - SPI0
11010 - XIP
11011 - XIP
11100 - MMC1
11101 - reserved
11110 - reserved
11111 - fast external boot

GPMC interface

0x8 = CS0 - on-SoM NAND flash (boot loader) 0x9 = CS1 - CAMAC interface 0xa = CS2 - not used 0xb = CS3 - not used

./gpmc 0x0a000000 0x12ff5678

CAMAC interface

General information:

  • CAMAC interface responds to GPMC CS3
  • the host CPU should always issue 32-bit read and write cycles on even addresses (last 2 bits of address set to 0)
  • address bits 15..12 address the FPGA GPMC registers (4 bits, 16 registers)
  • remaining address bits are used for encoding CAMAC operations
  • all GPMC registers are 32-bit wide

LEDs

                       ----
gpmc            0x0008 |OO| 0x0040
busy            0x0010 |OO| 0x0080
inhibit         0x0020 |OO| 0x0100
-----------------------------------------------------

Front Panel LEMO connectors

AAA

Firmware update

  • test the activer serial flash programmer interface
$ ./srunner_gpmc -id -16 /dev/null

Operation: Identify EPCS Device
bb_open!
Info: Found GPMC 0xABCD FlashProgrammer interface.

Info: Silicon ID - 0x14 
Info: Serial Configuration Device - EPCS16

Operation Completed!!!
  • write pof file to flash memory
$ ./srunner_gpmc -program -16 CAMAC_Crat_Controller.pof

Operation: Programming EPCS
Info: Programming file: "CAMAC_Crat_Controller.pof" opened.
Info: File size: 2097359 bytes.
Skipping POF file header: start of data at 154, file size 2097359, remain 2097205, modulo 1024 = 53
Final file size 2097152
bb_open!
Info: Found GPMC 0xABCD FlashProgrammer interface.

Info: Silicon ID - 0x14 
Info: Serial Configuration Device - EPCS16
Info: Erasing...
....................Info: Erase Done
Info: Start programming process.

Info: Programming 8192 pages...
Info: Programming successful
bb_close!

Operation Completed!!!
  • reboot the FPGA
lxdaq30:LINUX$ ./camac --reboot
CAMAC firmware: 0x14120407
rebooting FPGA...
CAMAC firmware: 0x14120711
lxdaq30:LINUX$

Register 1 - command

Write-only 32 bit register: 

command 1: CMD_reset: 0x
command 2: CMD_reconfigure
command 3: CMD_TestMode
command 4: CMD_Zero
command 5: CMD_Clear
command 6: CMD_Inhibit
command 7: CMD_WriteLED: 0xXXXX0007 -> write 0xXXXX to the LED bus

Register 2 - test read/write register

32-bit read/write register for testing GPMC bus communications

Register 3 - FPGA flash programmer

active-serial flash programmer interface (see srunner, srunner_vme and srunner_gpmc).

Register 4 and 5 - CAMAC command, write data and read data

A write cycle to the GPMC bus carries 16 bits of address and 32 bits of data: 

Address 16 bits (Quartus cmd_A[15..0])
----
15..12 - GPMC register address 
--
11 - not used
10 - not used
9 - not used
8..4 - CAMAC N[4..0]
--
3 - CAMAC F[4]
2 - CAMAC_start - set this bit to 1 to trigger a CAMAC operation. Value 0 is for testing the communications without running the CAMAC sequencer.
1 - not accessible
0 - not accessible
----

Data 32 bits: (Quartus cmd_D[31..0])
----
31..28 - CAMAC F[3..0]. (CAMAC F[4] is cmd_A[3])
27..24 - CAMAC A[3..0]
--
23..0 - CAMAC write lines W[24..1]
----

To verify correct data transmission on the GPMC bus and correct latching of the data in the CAMAC part of the FPGA, the 32 bits of data can be read back through register 4 and the 16 bits of address can be read through the low 16 bits of register 5. Reading from these registers is not necessary for operating CAMAC cycles.

Register 6 - CAMAC status and read data

Read-only 32 bit register: 

31 - not used
30 - not used
29 - not used
28 - BUSY_OUT
--
27 - BUSY
26 - set to 1 when CAMAC cycle is finished and new data is ready
25 - CMD_ACCPT
24 - RESPONSE
--
23..0 - CAMAC read data[24..1]

Register 7 - CAMAC LAM and interface status

Read-only 32-bit register: 

31 - EXT_BUSY
30 - EXT_INHIBIT
29 - EXT_GRANT_IN
28 - EXT_GRANT_OUT
--
27 - ACL
26 - RI
25 - not used
24 - not used
--
23..0 - CAMAC LAM from slots 24..1

Software commands

./gpmc 0x0b000000 # read firmware revision
./gpmc 0x0b001000 2 # reconfigure the fpga
./srunner_gpmc -id -64 /dev/null # use the flash programmer to read the flash chip identity
./srunner_gpmc -program -16 ../QUARTUS/output_files/CAMAC_Crat_Controller.pof # write POF file into the flash (remember to do an FPGA reconfigure to reboot into the new firmware)
./gpmc 0x0b001000 0x01f80007 # write to the LEDs
./gpmc 0x0b0040ac 0x00123456 # run some camac cycle
./gpmc 0x0b001000 0x80000003 # enable test mode
./gpmc 0x0b004174 0x00123456 # read from slot 23 - "manual input register"
./gpmc 0x0b00416c 0x00000000 # write to slot 22 - dataway display
./gpmc 0x0b00416c 0x00ffffff # write to slot 22 - dataway display
./gpmc 0x0b006000 # read CAMAC read data and status
./gpmc 0x0a00012c # reconfigure FPGA thorugh the CS2 line

./camac # read firmware revision, etc
./camac --reboot # reboot the FPGA
./camac --scan # scan CAMAC crate
./camac --gpmctest1 # test GPMC bus integrity - read/write test
./camac --gpmctest2 # test GPMC bus integrity - both data and address read/write test
./camac --testleds # test front panel LEDs - they should blink at 1Hz
./camac --testlemo # test front panel LEMOs - the voltages should alternate between 0V and ???V at 1Hz
./camac r # read CAMAC register r, e.g. \"./camac 0\" to read register 0 - firmware revision
./camac w v # write CAMAC register w with value v, e.g. \"./camac 2 0xabcd\" to write 0xabcd to test register 2
./camac n f a w # run a CAMAC cycle with given N, F, A, write data W


List of on-board hardware

End

AAA

Retrieved from "https://daq00.triumf.ca/DaqWiki/index.php?title=MityCAMAC&oldid=621"