VME-NIMIO32-Rev3: Difference between revisions
Jump to navigation
Jump to search
(→Links) |
|||
| Line 31: | Line 31: | ||
= Required board mods = | = Required board mods = | ||
* VME_LWORD | * VME_LWORD jumper to VME_SERB | ||
* VME_A29 jumper to ??? | |||
* RGB_LED_SDI jumper to ??? | |||
* 3.3V external power supply | |||
= Testing status = | |||
* power up ok | |||
* fpga jtag ok | |||
* flash load ok | |||
* fpga boot from flash ok | |||
* VME slave interface: A32/D32 single word cycle ok (minus VME_A29), 32-bit and 64-bit transfer untested (should work), 2eVME and 2eSST untested (should work). | |||
* VME interface: D lines: read ok, drive ok, A lines read ok (minus VME_A29), A lines drive untested. AS/DS read ok, drive untested. DTACK read ok, drive ok. | |||
* LVDS/ECL input: untested | |||
* NIM/TTL input/output: untested | |||
* SATA connectors: untested | |||
* clock cleaner: untested | |||
* ethernet interface: RX/TX untested, SPI untested, MAC flash untested | |||
= ZZZ = | = ZZZ = | ||
Revision as of 10:04, 8 April 2021
VME-NIMIO32-Rev3
Links
- https://edev-group.triumf.ca/hw/vme/vme_nimio/rev3
- https://bitbucket.org/ttriumfdaq/vmeio/src/master/
General information
Hardware
- FPGA: Cyclone5 5CGXFC7D7F27C8N
- boot flash: EPCQ256
- clock cleaner: IDT 8T49N241-009NLG1, I2C addr 1111'100b
- mac address: Microchip 24AA02E48T-I/OT, I2C address 0xA0, bus MAC_SCL, MAC_SDA
- eeprom: Microchip 24AA04T-I/OT, I2C address 0xA0, bus SCLK, SDATA
- clocks: OSC1, OSC2: 125 MHz, OSC3: 10 MHz
- SATA connectors: 2 on front panel
- SFP on front panel
Firmware
use /daq/quartus/13.1.3.178/quartus/bin/quartus
daq01:intelFPGA$ /daq/quartus/13.1.3.178/quartus/bin/jtagconfig 1) USB-Blaster [1-8] 02B030DD 5CGTFD7(B5|C5|D5)/5CGXBC7B6/..
Required board mods
- VME_LWORD jumper to VME_SERB
- VME_A29 jumper to ???
- RGB_LED_SDI jumper to ???
- 3.3V external power supply
Testing status
- power up ok
- fpga jtag ok
- flash load ok
- fpga boot from flash ok
- VME slave interface: A32/D32 single word cycle ok (minus VME_A29), 32-bit and 64-bit transfer untested (should work), 2eVME and 2eSST untested (should work).
- VME interface: D lines: read ok, drive ok, A lines read ok (minus VME_A29), A lines drive untested. AS/DS read ok, drive untested. DTACK read ok, drive ok.
- LVDS/ECL input: untested
- NIM/TTL input/output: untested
- SATA connectors: untested
- clock cleaner: untested
- ethernet interface: RX/TX untested, SPI untested, MAC flash untested