Electronic Logbook (ELOG)
Links
- /Elog ODB tree
- mhttpd
- mhttpd Elog Page
- Elog
- Melog Utility
- Elog Utility
Introduction
The Electronic LogBook (ELOG) is a utility built-in the web server. It is available and operational once the web-server is running. A dedicated button "ELOG" will be present on the main Midas status page for creating new entries. This mode is referred as the Built-in Elog.
This tool can replace the experimental logbook for daily entries. The main advantage of the Elog over a paper logbook is the possiblity to access it remotely, and provide a general knowledge of the experiment.
More recently, the independent Elog package can be linked to a Midas experiment. Its advantage over the built-in version is its flexibility. This package is used worldwide and improvements are constantly being made. A full-features documentation and standalone installation can be found at the Elog web site.
Built-in Elog
The ELOG page (accessed by clicking the Elog button if present on the main status page ) provides access to an electronic logbook. the Elog is not limited strictly to experiments. Worldwide Elog implementations can be found on the internet. This internal implementation doesn't requires any setup to be operational. The Elog is customized through the ODB /Elog tree.
External Elog
The external implementation requires a proper Elog installation which is fully described on the Elog web site. The External Elog implementation also requires a dedicated entry in the /Elog ODB tree as shown in the code below. It also requires the package Elog to be already installed, and properly configured. Once the ODB entry is present, the internal ELOG is disabled.
The External Elog is customized through the configuration file elogd.cfg (see Installation below).
Installation of External Elog
Installation requires requires several steps described below.
Download Elog package
- Download the Elog package from the web site mentioned above.
- Windows, Linux, Mac version can be found there. Simple installation procedures are also described. Its installation can be done at the system level or at the user level. The Elog can service multiple Electronic logbooks in parallel and therefore an extra entry in its configuration file can provide specific experimental elog in a similar fashion as the internal one.
Installation considerations
You need to take note of several considerations for its installation. Several locations are required for the different files that elog deals with.
- elog resource directory ( e.g. /elog_installation_dir where elog is installed)
- logbook directory (ex: /myexpt/logbook where the pwd and elog entries are stored).
- The pwd file uses encryption for the user password.
- As this Elog installation is tailored towards an experiment, a restriction applies i.e. ensure that the mhttpd and elog applications shares at least the same file system.
- This means that either both applications runs on the same machine or a nsf mount provides file sharing.
- You need to know the node and ports for both applications. Like mhttpd, elogd also requires a port number for communication through the web (e.g. NodeA:mhttpd -p 8080, NodeB:elogd -p 8081).
Configuration file elogd.cfg
- copy the default midas/src/elogd.cfg from the MIDAS distrbution to your operating directory.
- modify the elogd.cfg to reflect your configuration
# This is a simple elogd configuration file to work with MIDAS # [global] ; port under which elogd should run port = 8081 ; password file, created under 'logbook dir' password file = elog.pwd ; directory under which elog was installed (themes etc.) resource dir = /elog_installation_dir ; directory where the password file will end up logbook dir = /myexpt/logbook ; anyone can create it's own account self register = 1 ; URL under which elogd is accessible url = http://NodeB.triumf.ca:8081 ; the "main" tab will bring you back to mhttpd main tab = Xenon ; this is the URL of mhttpd which must run on a different port main tab url = http://NodeA:8080 ; only needed for email notifications smtp host = your.smtp.host ; Define one logbook for online use. Severl logbooks can be defined here [MyOnline] ; directory where the logfiles will be written to Data dir = /myexpt/logbook Comment = My MIDAS Experiment Electronic Logbook ; mimic old mhttpd behaviour Attributes = Run number, Author, Type, System, Subject Options Type = Routine, Shift Summary, Minor Error, Severe Error, Fix, Question, Info, Modification, Alarm, Test, Other, Options System = General, DAQ, Detector, Electronics, Target, Beamline Extendable Options = Type, System ; This substitution will enter the current run number Preset Run number = $shell(odbedit -e myexpt -h NodeA -d Runinfo -c 'ls -v \"run number\"') Preset Author = $long_name Required Attributes = Type, Subject ; Run number and Author cannot be changed Locked Attributes = Run number, Author Page Title = ELOG - $subject Reverse sort = 1 Quick filter = Date, Type, Author ; Don't send any emails Suppress email to users = 1
Start the Elog daemon
- start the elog daemon. -x is for the shell substitution of the command Preset Run number = $shell(...)
- The argument invokes the odbedit remotely if needed to retrieve the current run number. You will have to ensure the proper path to the odbedit and the proper -e, -h arguments for the experiment and host.
You may want to verify this command from the console.
NodeB:~>/installation_elog_dir/elogd -c elogd.cfg -x<cr> starts the mhttpd at its correct port and possibly in the daemon form. NodeA:~>mhttpd -p 8080 -D
Activate External Elog
At this point the Elog from the MIDAS web page is accessing the [[[#Built-in Elog|Built-in]]] (internal) Elog. To activate the external Elog you need to edit two ODB variables (which mhttpd automatically created):
- string /Elog/URL needs to be set to the URL of the external ELOG.
- bool /Elog/External Elog needs to be set to 'y'
Confirm proper operation of the external Elog by creating an entry. You will be prompted for a username and password. Click on New registration. Full control of these features are described in the Elog documentation. Stop and restart the Elogd in the background.
NodeB:~>/installation_elog_dir/elogd -c elogd.cfg -x -D
How to convert Built-in Elog files to External files
In the event you had a previous entry under the internal elog, you can convert the internal to external using the elconv tool.
NodeB:~> cp internal/elog_logbook/*.log /myexpt/logbook/. NodeB:~> cd /myexpt/logbook NodeB:~> /installation_elog_dir/elconv
How to send entries to the Elog from a script
Utilities exist to send elog entries automatically (e.g. from a script run at begin-of-run). Use melog to send an entry to a Built-in elog, or elog to send an entry to an external elog.