A bit of update to the mlogger. In preparation for more cleanup when Stefan is 
here at TRIUMF.

1) fix overwrite of existing files if run number is reset (check for existing 
files was missing in the LZ4, BZ2 & co data path)
2) made output files read-only (midas, json and checksum files)
3) commented out the old code paths

Currently active per-channel ODB settings:

Active - enable or disable mlogger channel
Type - NOT USED
Filename - output filename template, %d are replaced by run number and subrun 
number, also pipe command for PIPE output
Format - NOT USED
Compression - NOT USED
ODB dump - enable/disable writing ODB dump to data file
ODB dump format - "json" is recommended for new experiments
Log messages - write log messages to output file, 0=off, -1=write all messages
Buffer - "SYSTEM" read events from this event buffer
EventID - "-1" for all events
Trigger Mask - "-1" for all events
Event Limit - stop run after so many events
Byte Limit - stop run after so many bytes
Subrun Byte limit - switch to next subrun file after writing so many bytes. 
actual file size is longer than subrun_byte_limit because of ODB dumps.
Tape Capacity - NOT USED
Subdir Format - if not empty, output file name is DIR/SUBDIR/FILENAME, "%" 
format things are expanded by strftime().
Current Filename - updated by mlogger, contains the currently written file name
Data checksum - checksum before compression, use CRC32C for maximum speed, 
SHA512 for maximum security.
File checksum - checksum after compression, CRC32C is good against accidental 
file corruption, SHA512 is cryptographically strong, good against purposeful 
tampering.
Compress - use "lz4" for maximum speed, bzip2 or pbzip2 for maximum compression. 
no compression and gzip are not recommended. (ZFS may apply lz4 compression to 
uncompressed data).
Output - "NULL" do not write anything, "FILE" write to disk, "FTP" write to FTP 
server, "ROOT" write via the mlogger ROOT writer (docs?), "PIPE" pipe data 
through an external command (i.e. for bzip2 compression).
Gzip compression - gzip compression flags (see gzip docs, 1=max speed, 9=max 
compression)
Bzip2 compression - if non-zero, bzip2 compression level (see "bzip2 -h", 1=max 
speed, 9=max compression)
Pbzip2 num cpu - number of CPUs used by parallel bzip2 compression, pbzip2 -p 
flag
Pbzip2 compression - if non-zero, pbzip2 compresison level (see "pbzip2 -h", 
default is 9=max compression)
Pbzip2 options - any additional pbzip2 options, i.e. -l, -m, -p, etc.

Currently active /Logger options:

Data Dir - where to write all output files, if empty, cm_get_path() is used.
Message file date format - not used in mlogger
Message dir - not used in mlogger
Write data - if set to "no", midas file, runlog, etc will not be written.
ODB Dump - at run stop, save odb to disk
ODB Dump File - file name for "ODB Dump" save file. "%d" is replaced by run 
number. "json" format is recommended for new experiments.
ODB Last Dump File - at run start, save ODB to disk. "json" format is 
recommended for new experiments.
Auto restart - run stopped by time limit or event limit is automatically 
restarted
Auto restart delay - wair for some many seconds before restarting the run
Tape message - NOT USED
Run duration - stop the run after so many seconds
Next subrun - change from "no" to "yes" to force mlogger to open a new subrun 
file (should this be per-channel?)
Subrun duration - open new subrun file after so many seconds (should this be 
per-channel?)
History dir - not used in mlogger
Detached transition - "no" use the normal multithreaded transtions 
(recommended), "yes" use mtransition helper to stop and restart runs. sometimes 
files because mtransition is not in the user $PATH or wrong version of 
mtransition is in the user $PATH.

K.O.