The short term solution would be to increase the logger timeout in the ODB under

/Programs/Logger/Watchdog timeout

and set it to 6000 (one minute). But that is curing just the symptoms. It would be 
interesting to understand the cause of this error. Probably the logger takes more than 10 
seconds to start or stop the run. The reason could be that the history grow too big (what 
we have right now in MEG II), or some disk problems. But that needs detailed debugging on 
the logger side.

Stefan

Hello,
     I'm experiencing crashes of the mlogger program on the time scale of a couple 
of days. The only messages from MIDAS are:

05:34:47.336 2021/10/24 [mhttpd,INFO] Client 'Logger' (PID 14281) on database 
'ODB' removed by db_cleanup called by cm_periodic_tasks (idle 10.2s,TO 10s)
05:34:47.335 2021/10/24 [mhttpd,INFO] Client 'Logger' on buffer 'SYSMSG' removed 
by cm_periodic_tasks (idle 10.2s, timeout 10s)

Any suggestion to further investigate this issue?

Thank you very much,
         Francesco

It worked, thank you very much!

Francesco

> > Enable IPv6                     y
> 
> Probably the IPv6 problem, see here elog:2269
> 
> I asked to turn off IPv6 by default, or at least mention this in the documentation,
> but unfortunately nothing happened.
> 
> Stefan

> Enable IPv6                     y

Probably the IPv6 problem, see here elog:2269

I asked to turn off IPv6 by default, or at least mention this in the documentation,
but unfortunately nothing happened.

Stefan

Dear all,
      I am trying to make the MIDAS web server for my DAQ project accessible from other machines. In the ODB, I activated the necessary flags:

[local:CYGNUS_RD:S]/WebServer>ls
Enable localhost port           y
localhost port                  8080
localhost port passwords        n
Enable insecure port            y
insecure port                   8081
insecure port passwords         y
insecure port host list         y
Enable https port               y
https port                      8443
https port passwords            y
https port host list            n
Host list
                                localhost
Enable IPv6                     y
Proxy                           
mime.types

Following the instructions on the Wiki I enabled the SSL support. When running mhttpd, I get these messages:

Mongoose web server will use HTTP Digest authentication with realm "CYGNUS_RD" and password file "/home/cygno/DAQ/online/htpasswd.txt"
Mongoose web server will use the hostlist, connections will be accepted only from: localhost
Mongoose web server listening on http address "localhost:8080", passwords OFF, hostlist OFF
Mongoose web server listening on http address "[::1]:8080", passwords OFF, hostlist OFF
Mongoose web server listening on http address "8081", passwords enabled, hostlist enabled
[mhttpd,ERROR] [mhttpd.cxx:19166:mongoose_listen,ERROR] Cannot mg_bind address "[::0]:8081"
Mongoose web server will use https certificate file "/home/cygno/DAQ/online/ssl_cert.pem"
Mongoose web server listening on https address "8443", passwords enabled, hostlist OFF
[mhttpd,ERROR] [mhttpd.cxx:19166:mongoose_listen,ERROR] Cannot mg_bind address "[::0]:8443"

and the server is not accessible from other machines. Any suggestion to solve or better investigate this problem?

Thank you very much,
         Francesco

> Creating an ODB key requires users to know the Type ID that are defined in 
> https://bitbucket.org/tmidas/midas/src/develop/include/midas.h starting at line 320.
> 
> I can't find any information on the Midas Wiki about these values or how to find 
> them.
> 
> Am I missing something obvious?  Is there a way to improve how to find these values?  
> Or is this not the best way to interact with the ODB?

Well, you found them in midas.h, so where is the problem?

If you want a more detailed description, just look in the midas documentation (RTFM):

https://midas.triumf.ca/MidasWiki/index.php/Midas_Data_Types

If you want a more modern interface to the ODB without these data types, look here:

https://midas.triumf.ca/MidasWiki/index.php/Odbxx

Best regards,
Stefan

Creating an ODB key requires users to know the Type ID that are defined in 
https://bitbucket.org/tmidas/midas/src/develop/include/midas.h starting at line 320.

I can't find any information on the Midas Wiki about these values or how to find 
them.

Am I missing something obvious?  Is there a way to improve how to find these values?  
Or is this not the best way to interact with the ODB?

The midas forum software (elogd) was updated to latest version and moved from our old server 
(ladd00.triumf.ca) to our new server (daq00.triumf.ca).

The following URLs should work:

https://daq00.triumf.ca/elog-midas/Midas/ (new URL)
https://midas.triumf.ca/elog/Midas/ (old URL, redirects to daq00)
https://midas.triumf.ca/forum (link from midas wiki)

The configuration on the old server ladd00.triumf.ca is quite tangled between
several virtual hosts and several DNS CNAMEs. I think I got all the redirects
correct and all old URLs and links in old emails & etc still work.

If you see something wrong, please reply to this message here or email me directly.

K.O.

> > > test, no email. K.O.
> > 
> > test reply, no email. K.O.
> 
> test attachment, no email. K.O.

test email. K.O.

> > test, no email. K.O.
> 
> test reply, no email. K.O.

test attachment, no email. K.O.

> test, no email. K.O.

test reply, no email. K.O.

test, no email. K.O.

A requested change in the history logging system has been made today. Previously, history values were
logged with a maximum frequency (usually once per second) but also with a minimum frequency, meaning
that values were logged for example every 60 seconds, even if they did not change. This causes a problem.
If a frontend is inactive or crashed which produces variables to be logged, one cannot distinguish between
a crashed or inactive frontend program or a history value which simply did not change much over time.
The history system was designed from the beginning in a way that values are only logged when they actually
change. This design pattern was broken since about spring 2021, see for example this issue:

https://bitbucket.org/tmidas/midas/issues/305/log_history_periodic-doesnt-account-for

Today I modified the history code to fix this issue. History logging is now controlled by the value of 
common/Log history in the following way:

* Common/Log history = 0 means no history logging
* Common/Log history = 1 means log whenever the value changes in the ODB
* Common/Log history = N means log whenever the value changes in the ODB and 
  the previous write was more than N seconds ago

So most experiments should be happy with 0 or 1. Only experiments which have fluctuating values due to noisy 
sensors might benefit from a value larger than 1 to limit the history logging. Anyhow this is not the preferred 
way to limit history logging. This should be done by the front-end limiting the updates to the ODB. Most of the 
midas slow control drivers have a “threshold” value. Only if the input changes by more then the threshold are 
written to the ODB. This allows a per-channel “dead band” and not a per-event limit on history logging 
as ‘log history’ would do. In addition, the threshold reduces the write accesses to the ODB, although that is
only important for very large experiments.

Stefan

Dear all,
     I need to integrate in my MIDAS project the communication with an OPC UA 
server. My plan is to develop an OPC UA client as a "device" in 
midas/drivers/device.

Two questions:

1) Is anybody aware of some similar effort for some other project, so that I can 
get some example?

2) What could be the more appropriate driver's class to be used? generic.cxx? 
multi.cxx?

Thank you for your help,
           Francesco

> Thank you, Stefan.
> 
> I found these instructions under
> 1) The changelog: https://midas.triumf.ca/MidasWiki/index.php/Changelog#2020-12
> 2) Konstantin's elog announcements (e.g. https://midas.triumf.ca/elog/Midas/2089)
> 
> I do see reference to updating the submodules under the TRIUMF install 
> instructions 
> (https://midas.triumf.ca/MidasWiki/index.php/Setup_MIDAS_experiment_at_TRIUMF#Inst
> all_MIDAS) although perhaps it can be clarified.
> 
> Cheers,
> Richard

Hi Richard,

I updated the documentation at

https://midas.triumf.ca/MidasWiki/index.php/Changelog#Updating_midas

by putting the submodule update command everywhere.

Best,
Stefan

Thank you, Stefan.

I found these instructions under
1) The changelog: https://midas.triumf.ca/MidasWiki/index.php/Changelog#2020-12
2) Konstantin's elog announcements (e.g. https://midas.triumf.ca/elog/Midas/2089)

I do see reference to updating the submodules under the TRIUMF install 
instructions 
(https://midas.triumf.ca/MidasWiki/index.php/Setup_MIDAS_experiment_at_TRIUMF#Inst
all_MIDAS) although perhaps it can be clarified.

Cheers,
Richard

> 1) git clone https://bitbucket.org/tmidas/midas --recursive
> 2) cd midas
> 3) git checkout release/midas-2020-08
> 4) mkdir build
> 5) cd build
> 6) cmake ..
> 7) make

When you do step 3), you get

~/tmp/midas$ git checkout release/midas-2020-08
warning: unable to rmdir 'manalyzer': Directory not empty
warning: unable to rmdir 'midasio': Directory not empty
M	mjson
M	mscb
M	mvodb
M	mxml

The 'M' in front of the submodules like mscb tell you that you
have an older version of midas (namely midas-2020-08), but the 
*current* submodules, which won't match. So you have to roll back
also the submodules with:

3.5) git submodule update --recursive

This fetched those versions of the submodules which match the
midas version 2020-08. See here for details: 

https://git-scm.com/book/en/v2/Git-Tools-Submodules

From where did you get the command

git checkout release/xxxx ???

If you tell me the location of that documentation, I will take
care that it will be amended with the command

git submodule update --recursive

Best,
Stefan

All,

I am performing a fresh install of MIDAS on an Ubuntu linux box. I follow the 
usual installation procedure:

1) git clone https://bitbucket.org/tmidas/midas --recursive
2) cd midas
3) git checkout release/midas-2020-08
4) mkdir build
5) cd build
6) cmake ..
7) make

Step 3 warns me that 
"warning: unable to rmdir 'manalyzer': Directory not empty" and 
"warning: unable to rmdir 'midasio': Directory not empty"

Step 7 fails.
Compilation fails with an mhttp error related to mscb:
mhttpd.cxx:8224:59: error: too few arguments to function 'int mscb_ping(int, 
short unsigned int, int, int)'
 8224 |             status = mscb_ping(fd, (unsigned short) ind, 1);


I was able to get around this by rolling mscb back to some old version (commit 
74468dd), but am extremely nervous about mix-and-matching the code this way.

Any advice would be greatly appreciated.

Cheers,
Richard 

Not sure how many people are using it, but the Chat facility in midas was broken 
for some time now and got fixed today again.

Just for your information: Chat can be used like WhatsApp & Co, and connects all 
people who access a midas experiment through their browser. It's good to 
communicate between shift crew members located at different places. One advantage 
is that the chat messages can get 'spoken' by the text-to-speech engine of your 
browser, so it can be used to "wake up" shifters. Can be configured through the 
"Config" page.

Stefan

To limit the impact of the numerous crashes of mhttpd, I installed the monit tool at MEG at PSI 
(https://en.wikipedia.org/wiki/Monit). It monitors mhttpd, and if it cannot connect to it for a certain
time, it kills the process and restarts it. This covers endless loops, simple crashes (caused by the
known multi-threading issue in mongoose), and also cases where mhttpd develops a memory leak and becomes
unresponsive. 

To configure monit for mhttpd, first install the package, make sure the daemon gets started automatically
after reboot (typically "sysemctl enable monit"), and put the attached file into

/etc/monit.d/mhttpd

You have to adjust the <path-to-midas> according to your midas installation, and probably also the port
under which mhttpd is listening (8082 in my case). Put 

set daemon 10

into /etc/monitrc if you want monit to check mhttpd every 10 seconds (default is 30 seconds). Then, every
10 seconds monit request "midas.css" from mhttpd, and if it cannot obtain it after 30 seconds, it kills
mhttpd and restarts it.

Loading long history plots taking more than 30 seconds should probably not be an issue since mhttpd is 
multi-threaded, but I haven't tested this in detail.

Attached below is a typical status page produced by monit, which has its own built-in web server (normally
listening at port 2812, accessible only from localhost by default).

I hope this helps some of you.

Stefan