deap00:/dev/sdc 1517478241 dev="/dev/sdc"> smartctl 5.43 2012-06-30 r3573 [x86_64-linux-2.6.32-642.6.2.el6.x86_64] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda (SATA 3Gb/s, 4K Sectors) Device Model: ST3000DM001-9YN166 Serial Number: W1F0SG0W LU WWN Device Id: 5 000c50 0529ea8a7 Firmware Version: CC4B User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Thu Feb 1 04:44:02 2018 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 331) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 086 085 006 Pre-fail Always - 221657136 3 Spin_Up_Time 0x0003 092 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 194 5 Reallocated_Sector_Ct 0x0033 079 079 036 Pre-fail Always - 28640 7 Seek_Error_Rate 0x000f 085 060 030 Pre-fail Always - 341048727 9 Power_On_Hours 0x0032 047 047 000 Old_age Always - 46913 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 194 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 355 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 17180196884 189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 201 190 Airflow_Temperature_Cel 0x0022 069 050 045 Old_age Always - 31 (Min/Max 20/39) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 100 193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 5583 194 Temperature_Celsius 0x0022 031 050 000 Old_age Always - 31 (0 13 0 0 0) 197 Current_Pending_Sector 0x0012 100 001 000 Old_age Always - 72 198 Offline_Uncorrectable 0x0010 100 001 000 Old_age Offline - 72 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 29 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 161559489851156 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 265627218500179 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 87907447293333 SMART Error Log Version: 1 ATA Error Count: 353 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 353 occurred at disk power-on lifetime: 46909 hours (1954 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 40 ff ff ff ef 00 25d+19:57:30.990 READ DMA EXT 35 00 20 ff ff ff ef 00 25d+19:57:30.990 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:57:30.990 WRITE DMA EXT 35 00 10 ff ff ff ef 00 25d+19:57:30.989 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:57:30.989 WRITE DMA EXT Error 352 occurred at disk power-on lifetime: 46909 hours (1954 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 90 ff ff ff ef 00 25d+19:50:50.874 READ DMA EXT 35 00 08 ff ff ff ef 00 25d+19:50:50.873 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:50:50.873 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:50:50.873 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:50:50.873 WRITE DMA EXT Error 351 occurred at disk power-on lifetime: 46909 hours (1954 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 25d+19:50:46.054 READ DMA EXT ef 10 02 00 00 00 a0 00 25d+19:50:46.053 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 25d+19:50:46.053 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 25d+19:50:46.052 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 25d+19:50:46.052 SET FEATURES [Set transfer mode] Error 350 occurred at disk power-on lifetime: 46909 hours (1954 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 25d+19:50:43.016 READ DMA EXT 35 00 08 ff ff ff ef 00 25d+19:50:42.994 WRITE DMA EXT ca 00 08 30 17 c0 eb 00 25d+19:50:42.993 WRITE DMA ca 00 08 18 17 c0 eb 00 25d+19:50:42.993 WRITE DMA ea 00 00 00 00 00 a0 00 25d+19:50:42.940 FLUSH CACHE EXT Error 349 occurred at disk power-on lifetime: 46908 hours (1954 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 58 ff ff ff ef 00 25d+19:42:38.466 READ DMA EXT 35 00 08 ff ff ff ef 00 25d+19:42:38.466 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:42:38.466 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:42:38.378 WRITE DMA EXT 35 00 08 ff ff ff ef 00 25d+19:42:38.378 WRITE DMA EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.