vera00:/dev/sdc 1715171101 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.15.0-105-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD201KFGX-68BKJN0 Serial Number: 9AG8DA8E LU WWN Device Id: 5 000cca 2edc3d142 Firmware Version: 83.00A83 User Capacity: 20,000,588,955,648 bytes [20.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-5 (minor revision not indicated) SATA Version is: SATA >3.3 (10), 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed May 8 05:25:01 2024 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (2263) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 001 Pre-fail Always - 0 2 Throughput_Performance 0x0004 148 148 000 Old_age Offline - 48 3 Spin_Up_Time 0x0007 100 100 001 Pre-fail Always - 69 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1 5 Reallocated_Sector_Ct 0x0033 100 100 001 Pre-fail Always - 0 7 Seek_Error_Rate 0x000a 100 100 000 Old_age Always - 0 8 Seek_Time_Performance 0x0004 140 140 000 Old_age Offline - 15 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1813 10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1 22 Unknown_Attribute 0x0023 100 100 025 Pre-fail Always - 6553700 90 Unknown_Attribute 0x0031 100 100 001 Pre-fail Offline - 309237645312 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 80 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 80 194 Temperature_Celsius 0x0002 047 047 000 Old_age Always - 46 (Min/Max 23/51) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 1 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 25 hours (1 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 43 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 78 38 a6 0d 40 08 1d+01:10:31.271 READ FPDMA QUEUED 60 00 58 38 a3 0d 40 08 1d+01:10:31.270 READ FPDMA QUEUED 60 00 70 38 a2 0d 40 08 1d+01:10:31.270 READ FPDMA QUEUED 60 00 90 38 a1 0d 40 08 1d+01:10:31.270 READ FPDMA QUEUED 60 00 88 38 a0 0d 40 08 1d+01:10:31.269 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.