DS-VX: Difference between revisions
(Created page with "= DS-VX = Darkside Digitizer: [https://caen.it/products/vx2745/ CAEN VX2745] == Connecting == Each digitizer has a webpage served at its local IP address, port 80. You can point your browser to this page after connecting. Connect to the vx in one of two ways: # Ethernet: if the module is setup with DHCP and a server has been configured. # USB: the module is configured to run as ethernet-over-usb. Download the driver from the downloads page or [https://caen.it/wp-...") |
No edit summary |
||
| Line 1: | Line 1: | ||
Darkside Digitizer: [https://caen.it/products/vx2745/ CAEN VX2745] | Darkside Digitizer: [https://caen.it/products/vx2745/ CAEN VX2745] | ||
= Connecting = | |||
Each digitizer has a webpage served at its local IP address, port 80. You can point your browser to this page after connecting. | Each digitizer has a webpage served at its local IP address, port 80. You can point your browser to this page after connecting. | ||
| Line 19: | Line 17: | ||
The former adds the IP address to your /etc/hosts file, which then allows access. | The former adds the IP address to your /etc/hosts file, which then allows access. | ||
= Recovery Mode = | |||
To go into recovery mode, power down the board, and apply a jumper between the TX and RX terminals (as per [https://daq00.triumf.ca/elog-ds/DS-DAQ/279 this elog]). You can then point your browser to http://[fda7:cae0::1]/ to reset the firmware. There is no need to re-run <code>regPID.sh</code>. | To go into recovery mode, power down the board, and apply a jumper between the TX and RX terminals (as per [https://daq00.triumf.ca/elog-ds/DS-DAQ/279 this elog]). You can then point your browser to http://[fda7:cae0::1]/ to reset the firmware. There is no need to re-run <code>regPID.sh</code>. | ||
= Firmware Updates = | |||
Firmware is in an SVN repository (ask Yair for access) and is custom: contains some parts CAEN and some parts specific to Darkside. As of this writing the current firmware file is <code>V2745-OpenDPP-2026102907.cup</code>. | Firmware is in an SVN repository (ask Yair for access) and is custom: contains some parts CAEN and some parts specific to Darkside. As of this writing the current firmware file is <code>V2745-OpenDPP-2026102907.cup</code>. | ||
| Line 39: | Line 37: | ||
If the firmware update goes drastically wrong, go to [[#Recovery Mode|recovery mode]]. | If the firmware update goes drastically wrong, go to [[#Recovery Mode|recovery mode]]. | ||
= Software Updates = | |||
Software is on bitbucket: https://bitbucket.org/ttriumfdaq/dsproto_vx2740/src/develop/ | Software is on bitbucket: https://bitbucket.org/ttriumfdaq/dsproto_vx2740/src/develop/ | ||
| Line 45: | Line 43: | ||
Go to the setup section of the [https://bitbucket.org/ttriumfdaq/dsproto_vx2740/src/develop/README.md README] for installation notes. | Go to the setup section of the [https://bitbucket.org/ttriumfdaq/dsproto_vx2740/src/develop/README.md README] for installation notes. | ||
= Notable Elog Entries = | |||
* [https://daq00.triumf.ca/elog-ds/DS-DAQ/279 Recovery mode] | * [https://daq00.triumf.ca/elog-ds/DS-DAQ/279 Recovery mode] | ||
* [https://daq00.triumf.ca/elog-ds/DS-DAQ/307 Patching mac addresses] | * [https://daq00.triumf.ca/elog-ds/DS-DAQ/307 Patching mac addresses] | ||
Latest revision as of 19:07, 18 November 2026
Darkside Digitizer: CAEN VX2745
Connecting
Each digitizer has a webpage served at its local IP address, port 80. You can point your browser to this page after connecting.
Connect to the vx in one of two ways:
- Ethernet: if the module is setup with DHCP and a server has been configured.
- USB: the module is configured to run as ethernet-over-usb. Download the driver from the downloads page or get version 1.3 here. Then do the following from inside that extracted file:
sudo ./install.sh sudo ./regPID.sh
The former adds the IP address to your /etc/hosts file, which then allows access.
Recovery Mode
To go into recovery mode, power down the board, and apply a jumper between the TX and RX terminals (as per this elog). You can then point your browser to http://[fda7:cae0::1]/ to reset the firmware. There is no need to re-run regPID.sh.
Firmware Updates
Firmware is in an SVN repository (ask Yair for access) and is custom: contains some parts CAEN and some parts specific to Darkside. As of this writing the current firmware file is V2745-OpenDPP-2026102907.cup.
Firmware updates are accomplished via the webpage: Firmware (left panel) -> Upload new firmware (blue button).
Firmware updates will also update the webpage.
Note for 2026102907 firmware: the "Apply it after upload" is faulty (elog). Here are the steps to take instead (hopefully this is fixed in future versions):
- Upload the firmware to the board, without applying it (Big blue button)
- Mark it as default, without applying it (blue "..." -> More actions -> set as default)
- Reboot the board (top right username -> reboot device)
If the firmware update goes drastically wrong, go to recovery mode.
Software Updates
Software is on bitbucket: https://bitbucket.org/ttriumfdaq/dsproto_vx2740/src/develop/
Go to the setup section of the README for installation notes.