Hi Konstantin,

thanks for your reply.

> > thanks for your reply. I can confirm that your suggested workaround does indeed
> > make the problem dissapear.
> > I guess this issue hasn't been seen at T2K since we use MYSQL for the history.
> 
> I think you found the source of the problem, confused event id assignments. To confirm,
> can you email me (or post here) the output of odbedit "ls -l /History/Events".

Sorry, do you want this for after I've applied the fix suggested by Ben or with the original code 
that I posted.

With the original code it only shows one fe even though both are running:

[local:e666:S]History>ls -l /History/Events
Key name                        Type    #Val  Size  Last Opn Mode Value
---------------------------------------------------------------------------
1                               STRING  1     10    2m   0   RWD  FeDummy02
0                               STRING  1     16    2m   0   RWD  Run transitions

[local:e666:S]History> scl
Name                Host
mhttpd              localhost           
fedummy01           localhost           
fedummy02           localhost           
ODBEdit             localhost           
Logger              localhost           
[local:e666:S]History>ls "/History/Display/Default/Dummy/
Timescale                       1h
Zero ylow                       n
Show run markers                y
Show values                     y
Sort Vars                       n
Log axis                        n
Minimum                         0
Maximum                         0
Variables
                                FeDummy01:Data
                                FeDummy02:Data
Label
                                
                                
Colour
                                #00AAFF
                                #FF9000
Factor
                                0
                                0
Offset
                                0
                                0
Buttons
                                10m
                                1h
                                3h
                                12h
                                24h
                                3d
                                7d
Formula
                                
                                
Show old vars                   n

> If that's the problem, you can avoid it completely by switching to a history storage method
> that does not rely on magic mapping between equipment names and numeric event id's:
> try the "FILE" method (set odb /Logger/History/FILE/Active to "y", restart the logger) or
> the "MYSQL" method (you will need to setup a mysql database). You tell mhttpd and mhist which 
> history data to read by setting ODB /History/LoggerHistoryChannel to one of the channel names 
> from /logger/history/, restart mhttpd. (mhttpd and mhist used to print a message "reading history 
> data from channel XXX", but somebody removed this message).

Using the orginal code I posted and switching from MIDAS history to FILE history did not seem to 
change the random behaviour in the history plots.

Regards,

Nick.

> [local:e666:S]History>ls -l /History/Events
> Key name                        Type    #Val  Size  Last Opn Mode Value
> ---------------------------------------------------------------------------
> 1                               STRING  1     10    2m   0   RWD  FeDummy02
> 0                               STRING  1     16    2m   0   RWD  Run transitions

Something is very broken. There should be more entries here, at least
there should be entries for "FeDummy01" and usually there is also an entry
for "FeDummy" because one invariably runs fedummy without "-i" at least once.

The fact that changing from "midas" storage to "file" storage makes no difference
also indicates that something is very broken.

I want to debug this.

Since you tried the "file" storage, can you send me the output of "ls -l mhf*.dat" in the directory
with the history files? (it should have the "*.hst" files from the "midas" storage and "mhf*.dat" files
from the "file" storage.

K.O.

> > [local:e666:S]History>ls -l /History/Events
> > Key name                        Type    #Val  Size  Last Opn Mode Value
> > ---------------------------------------------------------------------------
> > 1                               STRING  1     10    2m   0   RWD  FeDummy02
> > 0                               STRING  1     16    2m   0   RWD  Run transitions
> 
> Something is very broken. There should be more entries here, at least
> there should be entries for "FeDummy01" and usually there is also an entry
> for "FeDummy" because one invariably runs fedummy without "-i" at least once.
> 
> The fact that changing from "midas" storage to "file" storage makes no difference
> also indicates that something is very broken.
> 
> I want to debug this.
> 
> Since you tried the "file" storage, can you send me the output of "ls -l mhf*.dat" in the directory
> with the history files? (it should have the "*.hst" files from the "midas" storage and "mhf*.dat" files
> from the "file" storage.


> 
> K.O.

Hi Konstantin,

> > [local:e666:S]History>ls -l /History/Events
> > Key name                        Type    #Val  Size  Last Opn Mode Value
> > ---------------------------------------------------------------------------
> > 1                               STRING  1     10    2m   0   RWD  FeDummy02
> > 0                               STRING  1     16    2m   0   RWD  Run transitions
> 
> Something is very broken. There should be more entries here, at least
> there should be entries for "FeDummy01" and usually there is also an entry
> for "FeDummy" because one invariably runs fedummy without "-i" at least once.

This is a fresh experiment that I started just to test this this issue, that is why there are not many 
entries in /History/Events. I agree though that we should expect to see a FeDummy01 entry.
 
> The fact that changing from "midas" storage to "file" storage makes no difference
> also indicates that something is very broken.
> 
> I want to debug this.
> 
> Since you tried the "file" storage, can you send me the output of "ls -l mhf*.dat" in the directory
> with the history files? (it should have the "*.hst" files from the "midas" storage and "mhf*.dat" 
files
> from the "file" storage.

When I started this experiment yesterday(?) I disabled the Midas history when I enbled the file 
history. Jsut now I reenabled the Midas history, so they are currently both active.

% ls -l work/online/{*.hst,mhf*.dat}
-rw-r--r-- 1 hastings hastings  14996 Sep 17 10:21 work/online/190917.hst
-rw-r--r-- 1 hastings hastings   3292 Sep 18 16:29 work/online/190918.hst
-rw-r--r-- 1 hastings hastings 867288 Sep 18 16:29 work/online/mhf_1568683062_20190917_fedummy01.dat
-rw-r--r-- 1 hastings hastings 867288 Sep 18 16:29 work/online/mhf_1568683062_20190917_fedummy02.dat
-rw-r--r-- 1 hastings hastings    166 Sep 17 10:17 
work/online/mhf_1568683062_20190917_run_transitions.dat

And again, just as a sanity check:

% odbedit -c 'ls -l /History/Events'
Key name                        Type    #Val  Size  Last Opn Mode Value
---------------------------------------------------------------------------
1                               STRING  1     10    1m   0   RWD  FeDummy02
0                               STRING  1     16    1m   0   RWD  Run transitions

Regards,

Nick.

We should fix this for midas-2019-10.

https://bitbucket.org/tmidas/midas/issues/193/confusion-in-history-event-ids

K.O.





> Hi Konstantin,
> 
> > > [local:e666:S]History>ls -l /History/Events
> > > Key name                        Type    #Val  Size  Last Opn Mode Value
> > > ---------------------------------------------------------------------------
> > > 1                               STRING  1     10    2m   0   RWD  FeDummy02
> > > 0                               STRING  1     16    2m   0   RWD  Run transitions
> > 
> > Something is very broken. There should be more entries here, at least
> > there should be entries for "FeDummy01" and usually there is also an entry
> > for "FeDummy" because one invariably runs fedummy without "-i" at least once.
> 
> This is a fresh experiment that I started just to test this this issue, that is why there are not many 
> entries in /History/Events. I agree though that we should expect to see a FeDummy01 entry.
>  
> > The fact that changing from "midas" storage to "file" storage makes no difference
> > also indicates that something is very broken.
> > 
> > I want to debug this.
> > 
> > Since you tried the "file" storage, can you send me the output of "ls -l mhf*.dat" in the directory
> > with the history files? (it should have the "*.hst" files from the "midas" storage and "mhf*.dat" 
> files
> > from the "file" storage.
> 
> When I started this experiment yesterday(?) I disabled the Midas history when I enbled the file 
> history. Jsut now I reenabled the Midas history, so they are currently both active.
> 
> % ls -l work/online/{*.hst,mhf*.dat}
> -rw-r--r-- 1 hastings hastings  14996 Sep 17 10:21 work/online/190917.hst
> -rw-r--r-- 1 hastings hastings   3292 Sep 18 16:29 work/online/190918.hst
> -rw-r--r-- 1 hastings hastings 867288 Sep 18 16:29 work/online/mhf_1568683062_20190917_fedummy01.dat
> -rw-r--r-- 1 hastings hastings 867288 Sep 18 16:29 work/online/mhf_1568683062_20190917_fedummy02.dat
> -rw-r--r-- 1 hastings hastings    166 Sep 17 10:17 
> work/online/mhf_1568683062_20190917_run_transitions.dat
> 
> And again, just as a sanity check:
> 
> % odbedit -c 'ls -l /History/Events'
> Key name                        Type    #Val  Size  Last Opn Mode Value
> ---------------------------------------------------------------------------
> 1                               STRING  1     10    1m   0   RWD  FeDummy02
> 0                               STRING  1     16    1m   0   RWD  Run transitions
> 
> Regards,
> 
> Nick.

This turned out to be a tricky problem. I am adding a warning about it in mlogger. This should go into midas-
2020-07. Closing bug #193. K.O.


> We should fix this for midas-2019-10.
> 
> https://bitbucket.org/tmidas/midas/issues/193/confusion-in-history-event-ids
> 
> K.O.
> 
> 
> 
> 
> 
> > Hi Konstantin,
> > 
> > > > [local:e666:S]History>ls -l /History/Events
> > > > Key name                        Type    #Val  Size  Last Opn Mode Value
> > > > ---------------------------------------------------------------------------
> > > > 1                               STRING  1     10    2m   0   RWD  FeDummy02
> > > > 0                               STRING  1     16    2m   0   RWD  Run transitions
> > > 
> > > Something is very broken. There should be more entries here, at least
> > > there should be entries for "FeDummy01" and usually there is also an entry
> > > for "FeDummy" because one invariably runs fedummy without "-i" at least once.
> > 
> > This is a fresh experiment that I started just to test this this issue, that is why there are not many 
> > entries in /History/Events. I agree though that we should expect to see a FeDummy01 entry.
> >  
> > > The fact that changing from "midas" storage to "file" storage makes no difference
> > > also indicates that something is very broken.
> > > 
> > > I want to debug this.
> > > 
> > > Since you tried the "file" storage, can you send me the output of "ls -l mhf*.dat" in the directory
> > > with the history files? (it should have the "*.hst" files from the "midas" storage and "mhf*.dat" 
> > files
> > > from the "file" storage.
> > 
> > When I started this experiment yesterday(?) I disabled the Midas history when I enbled the file 
> > history. Jsut now I reenabled the Midas history, so they are currently both active.
> > 
> > % ls -l work/online/{*.hst,mhf*.dat}
> > -rw-r--r-- 1 hastings hastings  14996 Sep 17 10:21 work/online/190917.hst
> > -rw-r--r-- 1 hastings hastings   3292 Sep 18 16:29 work/online/190918.hst
> > -rw-r--r-- 1 hastings hastings 867288 Sep 18 16:29 work/online/mhf_1568683062_20190917_fedummy01.dat
> > -rw-r--r-- 1 hastings hastings 867288 Sep 18 16:29 work/online/mhf_1568683062_20190917_fedummy02.dat
> > -rw-r--r-- 1 hastings hastings    166 Sep 17 10:17 
> > work/online/mhf_1568683062_20190917_run_transitions.dat
> > 
> > And again, just as a sanity check:
> > 
> > % odbedit -c 'ls -l /History/Events'
> > Key name                        Type    #Val  Size  Last Opn Mode Value
> > ---------------------------------------------------------------------------
> > 1                               STRING  1     10    1m   0   RWD  FeDummy02
> > 0                               STRING  1     16    1m   0   RWD  Run transitions
> > 
> > Regards,
> > 
> > Nick.

A user reported an issue that if they were to plot some history data from 
2019 (a range of one day), the plot would spend ~4 minutes loading then 
crash the browser tab. This seems to effect chrome (under default settings) 
and not firefox

I can reproduce the issue, "Data Being Loaded" shows, then the page and 
canvas loads, then all variables get a correct "last data" timestamp, then 
the 'Updating data ...' status shows... then the tab crashes (chrome)


It seems that the browser is loading all data until the present day (maybe 4 
Gb of data in this case). In chrome the tab then crashes. In firefox, I do 
not suffer the same crash, but I can see the single tab is using ~3.5 Gb of 
RAM

Tested with midas-2020-08-a up until the HEAD of develop

I could propose the user use firefox, or increase the memory limit in 
chrome, however are there plans to limit the data loaded when specifically 
plotting between two dates?

The history code is right now programmes in such a way that when you request
an old time window, then all data from that window until the present date
gets loaded. When we implemented that, this worked fine for data ranges of 
several years with a delay of just a few seconds. Of course one can only
load that specific window, but when the user then scrolls right, one has to
append new data to the "right side" of the array stored in the browser. If the
user jumps to another location, then the browser has to keep track of which 
windows are loaded and which windows not, making the history code much more 
complicated. Therefore I'm only willing to spend a few days of solid work
if this really becomes a problem. 

Are you sure that the delay comes from the browser or actually from mhttpd
digging through GBytes of history data? I realized that you need solid state
disks to get a real quick response.

Stefan

Poking at the behavior of this, its fairly clear the slow response is from the data 
being loaded off an HDD, when we upgrade this system we will allocate enough SSD 
storage for the histories.

Using Firefox has resolved this issue for the user's project here

Taking this down a tangent, I have a mild concern that a user could temporarily 
flood our gigabit network if we do have faster disks to read the history data. Have 
there been any plans or thoughts on limiting the bandwidth users can pull from 
mhttpd? I do not see this as a critical item as I can plan the future network 
infrastructure at the same time as the next system upgrade (putting critical data 
taking traffic on a separate physical network).

> Of course one can only
> load that specific window, but when the user then scrolls right, one has to
> append new data to the "right side" of the array stored in the browser. If the
> user jumps to another location, then the browser has to keep track of which 
> windows are loaded and which windows not, making the history code much more 
> complicated. Therefore I'm only willing to spend a few days of solid work
> if this really becomes a problem. 

For now the user here has retrieved all the data they need, and I can direct others 
towards mhist in the near future. Being able to load just a specific window would be 
very useful in the future, but I comprehend how it would be a spike in complexity.

 > Taking this down a tangent, I have a mild concern that a user could temporarily 
> flood our gigabit network if we do have faster disks to read the history data. Have 
> there been any plans or thoughts on limiting the bandwidth users can pull from 
> mhttpd?

I guess this will not be network limiting but CPU limiting of the mhttpd process. But I'm 
not 100% sure, depends on the actual hardware. But even if we improve the history 
retrieval to "window only", the user could request all data form 2010 to 2020. So one 
would need some code which estimates the amount of data, then tell the user "do you really 
want that?". But still, a novice user can simply click "yes" without much of a thought. So 
in conclusion I believe proper user training is better than software limits. Like the 
other guy "I did 'rm -rf /', and now nothing works any more, can you help?".

Stefan

> 
> Tested with midas-2020-08-a up until the HEAD of develop
> 

Just so you know, it took myself and Stefan quite a bit of effort
to improve memory and data handling in the new history plots
to be able to plot 1 year of data without bogging down too much. I got
to learn the google-chrome javascript cpu profiler, memory profiler
and the intricacies of javascript shift() and unshift() operators.

Before midas-2020-08-a, pressing the zoom-out button you would never
reach the javascript memory limit, the code would go into "100% cpu use"
and the browser tab will become progressively unresponsive well before
running out of memory. With the original code, our alpha-g history plots
could go back a few weeks at most, with the current code, we can go back
about 11 months. Compared to the old "C" history plots that can
do "last 10 years", no problem.

Loading all the history data into the browser is a design choice.

It has benefits and downsides.

The main benefit is that looking at immediate live data is much easier.

The main downside is that "plot last 10 years" becomes impossible.

As they say "appetite comes during eating", we have learned about these
downsides as we developed the new system. When we started, we did not
know much about javascript memory limits, cpu limits, etc. We did learn
a lot, though.

With the current code, we are limited to loading history data up to 50% of
the javascript memory limit. I know how to change the code to get up to 100%,
but I think it is not worth it, it still does not get as to plot "last 10 year".

We think the solution to recovering "last 10 years" capability is to use
binned data (which the history system can already deliver to javascript).
With binned data, the data volume in Mbytes remains constant, javascript
memory use has an upper-bound (we never use more memory than X Mbytes)
and data movement over the network is reduced.

Another way to look at this - typical display has only 1000-4000 vertical pixels,
it cannot physically display a bigger number of data points (no more
then 1 data point per pixel). So why load 1000000 data points when we only
can plot 1000-4000 of them?

So all the infrastructure for plotting binned data is already there,
but the javascript code still needs to be written. I think the biggest
challenge will be in blending or combining binned and unbinned data
on the same plot or in seamlessly switching the plot between binned and
unbinned data.

K.O.

>
> With the current code, we are limited to loading history data up to 50% of
> the javascript memory limit.
>

The javascript memory limit itself seems to be a moving target. (google javascript 
memory limit, and good luck!).

Historically, javascript did not have any memory or cpu use limits, but with
the raise of abusive web sites, bitcoin miners, etc, I see browsers clamp down
on allowed/allocated CPU use (inactive tabs are throttled down). memory use
is already clamped down severely, on a 64 GB computer, a browser tab
can only allocate a handful of GBs.

This throttling of browser tabs is already intrusive enough that we need
to be careful in programming midas web pages. for examples throttled events
are not firing at the same rate or in the same order as in active tabs.

One logical conclusion of these restrictions could be that, eventually,
google-chrome permits only just enough cpu and memory to run gmail.

K.O.

> 
> Are you sure that the delay comes from the browser or actually from mhttpd
> digging through GBytes of history data?
>

I think we will need to address this question "head-on". The history plot
will need to display the following information:

"time to load data from disk: N seconds, time to transfer data to javascript: M 
seconds, time to make the plot: Q seconds".

The second and third items are already available, the first one will need
to be computed in mhttpd and passed to javascript.

K.O.

>
> Taking this down a tangent, I have a mild concern that a user could temporarily 
> flood our gigabit network if we do have faster disks to read the history data.
>

By my measurements, right now our javascript code can reach 30-50-70% of Gige ethernet
bandwidth, so, no, we cannot flood the network just by making history plots.

(we cannot reach 100% because javascript code is not multithreaded,
it cycles through "request new data" and "decode javascript, make plot" states,
and the network is idle in this second state).

>
> Have there been any plans or thoughts on limiting the bandwidth users can pull from 
> mhttpd?
>

10gige networking is here (and 5 and 2.5 Gige, too). I would not worry too much
about saturating 1gige network interfaces.

>
> I do not see this as a critical item as I can plan the future network 
> infrastructure at the same time as the next system upgrade (putting critical data 
> taking traffic on a separate physical network).
>

10gige network between all computers, everything on SSD ZFS arrays, except
bulk data on ZFS HDD arrays (only for cost reasons $$$/TB).

K.O.

A new tag has been implemented to display history panels in custom pages, integrated in the 
new custom page design from 2017. The full documentation can be found at 

https://midas.triumf.ca/MidasWiki/index.php/New_Custom_Pages_(2017)#mhistory

Attached is a simple example of such a panel and the result. You have to rename triggerrate.txt to triggerrate.html if you want to use it (can't do it here since otherwise the browser wants to render it which does not work outside of midas).

Stefan

> A new tag has been implemented to display history panels in custom pages, integrated in the 
> new custom page design from 2017. The full documentation can be found at 
> 

As part of consolidating/cleaning the MIDAS Wiki documentation, the "New Custom Pages" was folded into the main "Custom Page".  So to see a
description of Stefan's new functionality please go to 

https://midas.triumf.ca/MidasWiki/index.php/Custom_Page#mhistory

<html>
<head>
   <title>Test</title>
   <link rel="stylesheet" href="midas.css">
   <script src="controls.js"></script>
   <script src="midas.js"></script>
   <script src="mhttpd.js"></script>
</head>
<body class="mcss" onload="mhttpd_init('Test');">

<div id="mheader"></div>
<div id="msidenav"></div>

<div id="mmain">
  <div name="mhistory" data-group="Test" data-panel="Test" data-scale="1m" style="width:600px;border:1px solid black;"></div>
</div>
</body>
</html>

OS: OSX 10.14.6 Mojave
MIDAS: Downloaded from repo on April 2021.

I have a slow control frontend doing the command/readout of a MPOD HV/LV. Since I am reading out the current that are in nA (after updating snmp), I wanted to multiply the number by 1e9.

I noticed the new "Formula" field (introduced in 2019 it seems) instead of the "Factor/Offset" I was used to. None of my entries seems to be accepted (after hitting save, when coming back thee field is empty).

Looking in ODB in "/History/Display/MPOD/HV (Current)/", the field "Formula" is a string of size 32 (even if I have multiple plots in that display). I noticed that the fields "Factor" and "Offset" are still existing and they are arrays with the correct size. However, changing the values does not seem to do anything.

Deleting "Formula" by hand and creating a new field as an array of string (of correct length) seems to do the trick: the formula is displayed in the History display config, and correctly used.