Dear all,
        I need to implement a DAQ sequence where a short run (100 events, which takes a couple of 
minutes) is taken every hour, with a long run in between two short runs. In the sequencer, I can do:

LOOP infinite

.... some ODB settings ....
     TRANSITION START
     WAIT events 100
     TRANSITION STOP

.... some ODB settings ....
     TRANSITION START
     WAIT seconds 3600
     TRANSITION STOP

ENDLOOP


I have two questions: 

- for the long run, I want to write on disk only a maximum number of events. I think I can suppress 
the event polling in the frontend, with an ODB query of the number of collected events. I'm 
wondering if there is a smarter way to do that. It is also ok if the run is stopped after a maximum 
number of events, but the subsequent short run should still start exactly after 1h from the previous 
short run. 

- with the script above, the real time lapse between the start of two short runs would depend on 
the duration of the short run itself. Is there a way to start the short run exactly 1 h after the starting 
of the previous short run?

Thank you in advance for your help,
              Francesco

Dear all,
         I'm running a DAQ frontend and it works well if one single run is
taken. If I try to take a second run right after, the run is performed but, when
stopping it, I get the error messages below. Any hint?

Thank you for your help,
      Francesco


11:42:24.012 2019/03/12 [mhttpd,ERROR] [midas.c:6022:cm_shutdown,ERROR] Killing
and Deleting client 'cygnus_daq' pid 12472

11:42:24.012 2019/03/12 [mhttpd,ERROR] [midas.c:6019:cm_shutdown,ERROR] Cannot
connect to client 'cygnus_daq' on host 'localhost', port 46341

11:42:24.012 2019/03/12 [mhttpd,ERROR] [midas.c:9539:rpc_client_connect,ERROR]
cannot connect to host "localhost", port 46341: connect() returned -1, errno 111
(Connection refused)

11:42:24.012 2019/03/12 [mhttpd,ERROR] [midas.c:10821:rpc_client_call,ERROR]
call to "cygnus_daq" on "localhost" RPC "rc_transition": error,
ss_recv_net_command() status 411

11:42:24.012 2019/03/12 [mhttpd,ERROR] [system.c:4715:ss_recv_net_command,ERROR]
error receiving network command header, see messages

11:42:24.011 2019/03/12 [mhttpd,ERROR] [system.c:4661:recv_tcp2,ERROR]
unexpected connection closure

11:42:23.994 2019/03/12 [cygnus_daq,ERROR] [midas.c:1951:,ERROR]
cm_disconnect_experiment not called at end of program

Dear all,
       I'm trying to compile MIDAS on MacOS 10.10 and I get this error:

/Users/francesco/MIDAS/midas/src/system.cxx:3187:18: error: use of undeclared identifier 
'CLOCK_REALTIME'
   clock_settime(CLOCK_REALTIME, &ltm);

Is it related to my (old) version of MacOS? Can I fix it somehow?

Thank you,
      Francesco

Dear all,
      I'm trying to use the logging on a mysql DB. Following the instructions on 
the Wiki, I recompiled MIDAS after installing mysql, and cmake with NEED_MYSQL=1 
can find it:

-- MIDAS: Found MySQL version 8.0.23

Then, I compiled my frontend (cmake with no options + make) and run it, but in the 
ODB I cannot find the tree for mySQL. I have only:

Logger/Runlog/ASCII

while I would expect also:

Logger/Runlog/SQL

What could be missing? Maybe should I add something in the CMakeList file or run 
cmake with some option?

Thank you,
      Francesco

I solved this, it was a failed "make clean" before recompiling. Now it works.

Sorry for the noise.

Francesco

> Dear all,
>       I'm trying to use the logging on a mysql DB. Following the instructions on 
> the Wiki, I recompiled MIDAS after installing mysql, and cmake with NEED_MYSQL=1 
> can find it:
> 
> -- MIDAS: Found MySQL version 8.0.23
> 
> Then, I compiled my frontend (cmake with no options + make) and run it, but in the 
> ODB I cannot find the tree for mySQL. I have only:
> 
> Logger/Runlog/ASCII
> 
> while I would expect also:
> 
> Logger/Runlog/SQL
> 
> What could be missing? Maybe should I add something in the CMakeList file or run 
> cmake with some option?
> 
> Thank you,
>       Francesco

Dear experts,
       while trying to readout a MIDAS file from a python script. I get the error below at the very first event. Any hint?

Thank you very much,
            Francesco

  File "/home/cygno/DAQ/offline/file_reader.py", line 9, in <module>
    for event in mfile:
  File "/home/cygno/DAQ/python/midas/file_reader.py", line 159, in __next__
    ev = self.read_next_event()
  File "/home/cygno/DAQ/python/midas/file_reader.py", line 264, in read_next_event
    return self.read_this_event_body()
  File "/home/cygno/DAQ/python/midas/file_reader.py", line 307, in read_this_event_body
    self.event.unpack_body(body_data, 0, self.use_numpy)
  File "/home/cygno/DAQ/python/midas/event.py", line 648, in unpack_body
    bank.fill_header_from_bytes(bank_header_data, self.is_bank_32(), self.is_bank_data_64bit_aligned())
  File "/home/cygno/DAQ/python/midas/event.py", line 298, in fill_header_from_bytes
    self.name = "".join(x.decode('ascii') for x in unpacked[:4])
  File "/home/cygno/DAQ/python/midas/event.py", line 298, in <genexpr>
    self.name = "".join(x.decode('ascii') for x in unpacked[:4])
UnicodeDecodeError: 'ascii' codec can't decode byte 0xc8 in position 0: ordinal not in range(128)

Dear all,
     I need to integrate in my MIDAS project the communication with an OPC UA 
server. My plan is to develop an OPC UA client as a "device" in 
midas/drivers/device.

Two questions:

1) Is anybody aware of some similar effort for some other project, so that I can 
get some example?

2) What could be the more appropriate driver's class to be used? generic.cxx? 
multi.cxx?

Thank you for your help,
           Francesco

Dear all,
      I am trying to make the MIDAS web server for my DAQ project accessible from other machines. In the ODB, I activated the necessary flags:

[local:CYGNUS_RD:S]/WebServer>ls
Enable localhost port           y
localhost port                  8080
localhost port passwords        n
Enable insecure port            y
insecure port                   8081
insecure port passwords         y
insecure port host list         y
Enable https port               y
https port                      8443
https port passwords            y
https port host list            n
Host list
                                localhost
Enable IPv6                     y
Proxy                           
mime.types

Following the instructions on the Wiki I enabled the SSL support. When running mhttpd, I get these messages:

Mongoose web server will use HTTP Digest authentication with realm "CYGNUS_RD" and password file "/home/cygno/DAQ/online/htpasswd.txt"
Mongoose web server will use the hostlist, connections will be accepted only from: localhost
Mongoose web server listening on http address "localhost:8080", passwords OFF, hostlist OFF
Mongoose web server listening on http address "[::1]:8080", passwords OFF, hostlist OFF
Mongoose web server listening on http address "8081", passwords enabled, hostlist enabled
[mhttpd,ERROR] [mhttpd.cxx:19166:mongoose_listen,ERROR] Cannot mg_bind address "[::0]:8081"
Mongoose web server will use https certificate file "/home/cygno/DAQ/online/ssl_cert.pem"
Mongoose web server listening on https address "8443", passwords enabled, hostlist OFF
[mhttpd,ERROR] [mhttpd.cxx:19166:mongoose_listen,ERROR] Cannot mg_bind address "[::0]:8443"

and the server is not accessible from other machines. Any suggestion to solve or better investigate this problem?

Thank you very much,
         Francesco

It worked, thank you very much!

Francesco

> > Enable IPv6                     y
> 
> Probably the IPv6 problem, see here elog:2269
> 
> I asked to turn off IPv6 by default, or at least mention this in the documentation,
> but unfortunately nothing happened.
> 
> Stefan

Hello,
     I'm experiencing crashes of the mlogger program on the time scale of a couple 
of days. The only messages from MIDAS are:

05:34:47.336 2021/10/24 [mhttpd,INFO] Client 'Logger' (PID 14281) on database 
'ODB' removed by db_cleanup called by cm_periodic_tasks (idle 10.2s,TO 10s)
05:34:47.335 2021/10/24 [mhttpd,INFO] Client 'Logger' on buffer 'SYSMSG' removed 
by cm_periodic_tasks (idle 10.2s, timeout 10s)

Any suggestion to further investigate this issue?

Thank you very much,
         Francesco

Dear all,
       I've a frontend writing a quite big bunch of data into a MIDAS bank (16bit output from a 4MP photo camera). 
I'm experiencing a writing speed problem that I don't understand. When the photo camera is triggered at a low rate (< 2 Hz) 
writing into the bank takes a very short time for each event (indeed, what I measure is the time to write and go back 
into the polling function). If I increase the rate to 4 Hz, I see that writing the first two events takes a sort time, 
but the third event takes a very long time (hundreds of ms), then again the fourth and fifth events are very fast, and 
the sixth is very slow. If I further increase the rate, every other event is very slow. The problem is not in the readout 
of the camera, because if I just remove the bank writing and keep the camera readout, the problem disappears. Can you 
explain this behavior? Is there any way to improve it?

Below you can also find the code I use to copy the data from the camera buffer into the bank. If you have any suggestion 
to improve it, it would be really appreciated.

Thank you very much,
          Francesco



  const char* pSrc = (const char*)bufframe.buf;

  for(int y = 0; y < bufframe.height; y++ ){

    //Copy one row
    const unsigned short* pDst = (const unsigned short*)pSrc;

    //go through the row
    for(int x = 0; x < bufframe.width; x++ ){

      WORD tmpData = *pDst++; 

      *pdata++ = tmpData;

    }

    pSrc += bufframe.rowbytes;

  }
 

Dear all,
        I finally succeeded to get a working driver for the communication with an OPC 
UA server. It is based on the open62541 library and I use it in combination with the 
generic.h driver class. This is still a crude implementation, but let me post it here, 
maybe it can be useful to somebody else.

BTW, if there is somebody more skilled than me with OPC UA and MIDAS drivers, who is 
willing to give suggestions for improving the implementation, it would be extremely 
appreciated.

Best Regards,
      Francesco



> Dear all,
>      I need to integrate in my MIDAS project the communication with an OPC UA 
> server. My plan is to develop an OPC UA client as a "device" in 
> midas/drivers/device.
> 
> Two questions:
> 
> 1) Is anybody aware of some similar effort for some other project, so that I can 
> get some example?
> 
> 2) What could be the more appropriate driver's class to be used? generic.cxx? 
> multi.cxx?
> 
> Thank you for your help,
>            Francesco

Dear all,
       I'm writing a very simple device driver starting from the nulldev.cxx 
example. 

I define an equipment as reported at the end of this message then, if all 
variables are Input variables, I define them with:

  mdevice device("myEquimpent", "Input", DF_INPUT | DF_MULTITHREAD, mydevice);
  device.define_var("Var1", 0.1);
  device.define_var("Var2", 0.1);
  ...

If all variables are output variables, I define them with:

  mdevice device("myEquipment", "Output", DF_OUTPUT | DF_MULTITHREAD, mydevice);
  device.define_var("Var1", 0.1);
  device.define_var("Var2", 0.1);

But I don't know what to do if I have mixed input and output variables in the same 
device. I think I can do:

  mdevice device_in("myEquipment", "Input", DF_INPUT | DF_MULTITHREAD, mydevice);
  device.define_var("Var1", 0.1);

  mdevice device_out("myEquipment", "Output", DF_OUTPUT | DF_MULTITHREAD, 
mydevice);
  device.define_var("Var2", 0.1);

but in this case, inside mydevice.cxx, I don't know how to distinguish Var1 and 
Var2, because they are both identified as channel 0.

Do you have any suggestion?

Thank you,
      Francesco




-------------------------------------------------------------------



   {"SourceMotor",                       /* equipment name */
    {7, 0,                       /* event ID, trigger mask */
     "SYSTEM",                  /* event buffer */
     EQ_SLOW,                   /* equipment type */
     0,                         /* event source */
     "MIDAS",                   /* format */
     TRUE,                      /* enabled */
     RO_ALWAYS,        /* read when running and on transitions */
     60000,                     /* read every 60 sec */
     0,                         /* stop run after this event limit */
     0,                         /* number of sub events */
     1,                         /* log history every event */
     "", "", ""} ,
    cd_multi_read,                 /* readout routine */
    cd_multi,                      /* class driver main routine */
   },

Dear experts,
         I would like to have some clarification about the meaning and use of the 
tags in the ODB under /History/Tags.

I noticed that, if a history plot is created, but the name of the corresponding 
variable is changed later and the plot is modified accordingly, the old name 
persists in the /History/Tags list along with the new one. So, it appears in the 
list of variables when a new history plot is created.

It seems not to compromise the functionalities of the history system, but it is 
prone to create confusion.

Is it the expected behavior? What is the correct procedure to follow if the name 
of a variable has to be changed?

Thank you,
     Francesco

Hi,

I've been doing some preliminary work to use at least the MIDAS
SQL history component for a new CERN experiment (Aegis). I wonder
whether there is any plan to support 64-bit signed/unsigned integer data types
in MIDAS. time_t on 64-bit architectures is actually signed 64-bit
(the 'easy' way to work around the 2038 crisis), and this may be enough to
cause problems.

Thanks.
Francesco Prelz
INFN Milano

Hello,

When I  connect to analyzer on a x86_64 processor(with Roody),  
a analyzer break with segmentation violation in the root_server_thread  function.
Same code are working fine on a 32bit processor.
As I found the problem are in exchanging of pointers between analyzer and client.
Before to send a pointer, it is saved a pointer in int (size=4, instead of 8) at
this place:
Index: src/mana.c
===================================================================
--- src/mana.c  (revision 3498)
+++ src/mana.c  (working copy)
@@ -5386,7 +5386,7 @@

             //write pointer
             message->Reset(kMESS_ANY);
-            int p = (POINTER_T) obj;
+            POINTER_T p = (POINTER_T) obj;
             *message << p;
             sock->Send(*message);


Sincerely Yours,
Fedor Ignatov 

Yes right, Problem of a segmentation violation is solved with this patch. Now it works
fine on x86_64.

Fedor 

> Do I understand you right? With your patch it works even on 64 bit, right? Or do you
> mean there is still a segmentation violation? Anyhow I committed your patch since the
> "int" is clearly incorrect.
> 
> - Stefan

I add the following to makefile and try to treat Darwin as FreeBSD/Linux.
But I failed.
============ 
#-----------------------
# This is for MacOS X
#
ifeq ($(OSTYPE), Darwin)
CC = gcc
OS_DIR = Darwin
OSFLAGS = -DOS_DARWIN -DOS_LINUX
LIBS = -lbsd -lcompat
SPECIFIC_OS_PRG =
endif
============

I got the following errors:
=============
gcc -c -g -O2 -Wall -Iinclude -Idrivers -LDarwin/lib -DINCLUDE_FTPLIB  
-DOS_DARWIN -DOS_FREEBSD -o Darwin/lib/midas.o src/midas.c
In file included from include/midasinc.h:45,
                 from include/msystem.h:114,
                 from src/midas.c:623:
/usr/include/string.h:112: error: conflicting types for `strlcat'
include/midas.h:1701: error: previous declaration of `strlcat'
/usr/include/string.h:113: error: conflicting types for `strlcpy'
include/midas.h:1700: error: previous declaration of `strlcpy'
In file included from include/msystem.h:114,
                 from src/midas.c:623:
include/midasinc.h:161:21: sys/vfs.h: No such file or directory
include/midasinc.h:164:17: pty.h: No such file or directory
src/midas.c:780: error: conflicting types for `dbg_malloc'
include/midas.h:1478: error: previous declaration of `dbg_malloc'
src/midas.c:817: error: conflicting types for `dbg_calloc'
include/midas.h:1479: error: previous declaration of `dbg_calloc'
src/midas.c:858: error: conflicting types for `strlcpy'
/usr/include/string.h:113: error: previous declaration of `strlcpy'
src/midas.c:892: error: conflicting types for `strlcat'
/usr/include/string.h:112: error: previous declaration of `strlcat'
gmake: *** [Darwin/lib/midas.o] Error 1
==========

Could anyone give me some hints. Thanks!

> In the Midas doc under "Quick Start"
> http://midas.triumf.ca/doc/html/quickstart.html
> you will find the proper cvs command for accessing the latest cvs Midas
> version. The public pwd is cvs. You will only be able to checkout/update the
> package.

I cannot checkout module:
------------
01:52:16: pc2075.psi.ch: Operation timed out
01:52:16: cvs [checkout aborted]: end of file from server (consult above
messages if any)
------------

Could anybody add download tar package in the WWW interface of CVS repository.
I know the original CGI script has such a feature. Thanks.