Suggestion from John and my reply.

> We have achieved very high rates, but only with some care.

> The biggest issue was to make sure when you compile the CAEN driver for the A3818 board that you turn on the MIDAS switch.  Without that problems occur with some 
> probability given by the number of bytes processed - which translates into very soon if you have a high rate.  (The underlying cause is that both MIDAS and the A3818
> use unix Alarm signals, but the CAEN folks have a compile option to turn this off.)

> We use as little as possible of the CAENDigitizerLibrary - instead we program the registers directly on the board.

> There is still some kind of memory leak which we have not yet tracked down, so every few hours we shut down the frontend then restart it. 

We use A2818 (PCI) - fiber - V2718 (Bridge) - VME - V1751.
I actually didn't find a MIDAS switch in the Makefile.

More suggestions from John and my reply.

> we also don't use the VME back plane - it's just too slow - mixing VME commands to plain modules and digitizer modules is unreliable....

> We use CAEN fiberoptic version 2 to talk to the digitizers directly, we have upto 12 digitizers, and can use all channels for several hours, and can fill to about 75% 
of the A3818 bandwidth... 

So far we are limitted to 30 MB/s, if tested with CAEN examples, for example, the wavedump program by CAEN.
I think is kind of the limit by IDE hard drive.
Unfortunately we are still far from that limit, only ~ 1 MB/s now.  :(

Dear guys,

I’m Zhi Li from China, and I’m now working on my graduation project, which now
basically gets stuck in the part of preparing the frontend for my FADC (CAEN
VX1721) using Midas.

Now the current set-up includes a VME crate, a CAEN v2718 (Optical Bridge and
Controller) and a CAEN VX1721(8ch 8bit 500MS/s Waveform digitizer). The hardware
set-up has been finished and I could capture the analog waveform using CAEN
software(wavedump). 

Could anyone please tell me what are the basic things to do for using MIDAS?
I’ve installed MIDAS in PC and it works well for CAMAC, but do I need any extra
hardware module on using VME crate? Also, how to download
Universe-II VME driver?

Thanks,
Li

Hi Pierre,

Thanks for your instructions. Before I run the wavedump software, I need to load a driver file for A2818, thus I think I've got this interface of A2818.

I would be grateful to have a look at the frontend example used for v1720 (closer to v1721 I suppose), would you be so kind to offer me the Makefile as well? I
really want to have a compilable/executable DAQ frontend for vme modules, and know better how to link to CAEN library in the Makefile.

About hardware currently used in the vme crate(A2818), there is a VME controller(V2718, CONET VME Bridge), and a FADC(VX1721 waveform digitizer). I'm now preparing
this DAQ system to compare relative quantum efficiency, timing resolution, 1 pe distribution of photomultipliers, also measure decay time of cosmic muons, and
electron spectrum. Humbly, I want to know your opinion on whether I need additional hardware to finish these experiments.

Thanks,
Li

> Hi Li,
> 
> You mention that you've got the wavedump working. It suggests that you have a A3818 
> interface, can you confirm that?
> 
> If so, you can make a Midas frontend using the CAEN libraries to access your VX1721. I can provide you with a frontend example used for the V1720 or V1740. The 
> modifications for the VX1721 shouldn't be too hard as most of the CAEN digitizers 
> are fortunately based on a similar configuration mechanism.
> If you have a Midas CAMAC frontend, the trick would be to replace the CAMAC calls by 
> the appropriate CAENComm_xxx() for the equivalent functionality.
> 
> Can you remind me what hardware do you have in your lab for acquisition?
> CAMAC controller, VME controller etc.
> 
> Cheers, PAA
> 
> > Dear guys,
> > 
> > I’m Zhi Li from China, and I’m now working on my graduation project, which now
> > basically gets stuck in the part of preparing the frontend for my FADC (CAEN
> > VX1721) using Midas.
> > 
> > Now the current set-up includes a VME crate, a CAEN v2718 (Optical Bridge and
> > Controller) and a CAEN VX1721(8ch 8bit 500MS/s Waveform digitizer). The hardware
> > set-up has been finished and I could capture the analog waveform using CAEN
> > software(wavedump). 
> > 
> > Could anyone please tell me what are the basic things to do for using MIDAS?
> > I’ve installed MIDAS in PC and it works well for CAMAC, but do I need any extra
> > hardware module on using VME crate? Also, how to download
> > Universe-II VME driver?
> > 
> > Thanks,
> > Li

Hi folks:

we've been running midas-1.9.5 for a few years here at Regina.  We are now
working on a larger cosmic ray testing that requires a second ADC and second TDC
module in our Camac crate (we use the hytek1331 controller by the way).  We're
baffled as to how to set this up properly.  Specifically we have tried:

frontend.c

/* number of channels */
#define N_ADC  12 
(changed this from the old '8' to '12', and it seems to work for Lecroy 2249)

#define SLOT_ADC0   10
#define SLOT_TDC0   9
#define SLOT_ADC1   15
#define SLOT_TDC1   14

Is this the way to define the additional slots (by adding 0, 1 indices)?

Also, we were not able to get a new bank (ADC1) working, so we used a loop to
tag the second ADC values onto those of the first.

If someone has an example of how to handle multiple ADCs and TDCs and
suggestions as to where changes need to be made (header files, analyser, etc)
this would be great.

Thanks, Zisis...

P.S.  I am attaching the relevant files.

Dear all,

I'm using MIDAS system and CAEN V1721 to digitize the waveform from photomultipliers ( 
and the link bridge to PC is V2718 ). I use BLTRead to read data of the digitizer, but 
I found that if the event counting rate is high ( about 100KB/s ), the communication 
of V1721 and PC would be suspended randomly, and I get an error code of -2. Could you 
give me some suggestion? Thanks a lot.

Hi

Not sure how the rest of you specify mhttpd to work with multiple experiments on
one machine, but it would seem not the same as me ;-)

when executing mhttpd with 

mhttpd -e "experimentname" -p "experimentport" -D 

that experiment name is not transfered to transitions as cm_transition never
specifies the experiment in the call to "transition STOP" etc.
the only flag it sends is a -d for debug if selected.

The result is that the stop and start button of the webinterface does not work,
and transitions sit endlessly doing nothing but consuming all the processor,
odbedit works fine though.

Does everyone else use an apache reverse proxy and or explicit experiment choice
in the url ?

As an aside in mhttpd.c in the reply to -? it states 2 -h options the second
should be a -e. line 13378.


Thanks
Sean

Hi

> > Not sure how the rest of you specify mhttpd to work with multiple experiments on
> > one machine, but it would seem not the same as me ;-)
> 
> Please note that there has been a change concerning multiple experiments inside 
> mhttpd. From revision 4346 on, mhttpd can only connect to one single experiment, 
> and the experiment name in the URL (aka ?exp=name) is not supported any more. So if 
> you have several experiments, you start several instances of mhttpd now on 
> different ports.

That i do with : 
mhttpd -p xx -e experiment_name -D

> 
> > that experiment name is not transfered to transitions as cm_transition never
> > specifies the experiment in the call to "transition STOP" etc.
> > the only flag it sends is a -d for debug if selected.
> 
> When connecting to an experiment, any midas client uses the ODB from that 
> experiment so lives in that "namespace". So one client can never call any client 
> from another experiment. So your problem must be something else. Of course there is 
> not parameter "experiment" passed to cm_transition() since the experiment is 
> implicitly defined by the ODB mhttpd is attached to.

Will have to look else where.

> 
> > The result is that the stop and start button of the webinterface does not work,
> > and transitions sit endlessly doing nothing but consuming all the processor,
> > odbedit works fine though.
> 
> I guess you have to do some debugging there. Note that "detached" transitions have 
> been implemented recently by Konstantin, so maybe your problem is related to that. 
> In this case Konstantin should check what's wrong.

cm_transition does a "system(str)" on line 3243 inside the "if(async_flag == DETACH)" of
line 3219, how does an external program know about the state of the originating mhttpd
process ? Surely that str which executes "mtransition ......." should get a -e
specifying the experiment explicitly ? probably a -h as well to be thorough.
The only other way that mtransition.cxx will be able to pull in the experimentname is
from the environment variable in its call to cm_get_environment(....) on its startup.


Ok after some testing .... 
If i start the mhttpd with the environment variable MIDAS_EXPT_NAME set then its happy
as mtransition inherits the environment of mhttpd so cm_get_environment(...) of
mtransition picks up the experiment. Similarly if i insert "-e experimentname" into the
string "str" that is passed in system(str) of line 3243. Then start and stop buttons work. 

Konstantin any comments.

I suppose i can live with starting mhttpd with the environment set before running, but
that kind of negates the command line argument to mhttpd. 

Thanks for the help

Sean

> > For one thing, looking at a given midas-using executable, how do I tell what version of midas it has inside?
> 
> Ther is a function cm_get_version() returning the version. As for the executable, all you can do is a
> 
> strings <executable> | grep 1.9

   A lot of programs have a commandline option, such as "--version", where they return the program version number then exit.  As well as the
program version number, the version number of the midas library it's linked with could also be returned (There can be more than one
libmidas.so on a system and this would show which one was currently being linked)

   Something I would find useful would be for the version number to identify precisely which version you have, i.e. not to have different
versions of midas given the same version number.  I've had problems earlier this year due to midas-1.9.3 changing several times between
January and July, while keeping the same number.  I think if "in-between" versions of midas are to be made available, they should contain a
revision number or date or something in the version number to identify them.

> For remote connections (through mserver), there is already a version check. If the minor version differs, you get a warning, if the major
> versions differ (1.>>9<<.4), the client won't start. So at least for remote connection you get a clue.

   Safety measures like these can sometimes get in the way, if you know what you're doing.  So unless there is absolutely no possibility of
success, I think checks such as this one should be overrideable (by a client option).

Chris

   Midas, version 1.9.5 of 7th October, was installed, with a few changes, on a
64 bit opteron computer, running linux.  For this processor, as for the alpha
processor, long integers and addresses are 64 bits.  We added a new flag in the
Makefile,

250a251
> ARCH   = $(shell uname -m)
377a379,381
> ifeq ($(ARCH),x86_64)
> OSFLAGS := $(OSFLAGS) -DX86_64
> endif

and extended the alpha-specific definitions, of DWORD and PTYPE, in midas.h to
include this case,

549c549
< #ifdef __alpha
---
> #if defined(__alpha) || defined(X86_64)
598c598
< #ifdef __alpha
---
> #if defined(__alpha) || defined(X86_64)

apart from this, there are a large number of cases where pointers are cast to
integers, without using the PTYPE definition.  These all need to be changed by
hand, although these conversions should probably be removed anyway - in almost
all cases they are unnecessary, as just differences are being calculated.

There were also a number of warnings, which we ignored, where printf format
strings specified long integers, but the argument was not a long integer.  Casts
should probably be added in all cases where the type of the argument can vary
depending on the machine.

A midas analyser was made, which was able to successfully replay some data, but
this was all that was tested.

Chris

   We've had mhttpd aborting regularly since upgrading from midas-1.9.3.  This
happens during elog queries, and is due to an elog file that was incorrectly
modified by hand.  The modification to the file occurred 6 months ago.
   el_retrieve(midas.c:15683) now has several assert statements, one of which
aborts the program on reading the bad entry.

   Why is assert used, instead of an error return from the function (if
necessary), and maybe an error message in the log file?  Assert statements are
often removed, using NDEBUG, for normal use.

Chris

   The problem elog entry had one character removed, so end-of-file came before
the end of the message.  This could probably occur without the file being
altered, if the disk containing the elog fills.

   A couple of experiments at triumf wanted certain important odb variables
displayed on their status page.  (There was already the possibility to show the
run comment)
   A new folder "/Experiment/Status Items" was created containing links to the
variables of interest, these items are show on the status page, under the run
comment (if any), in 3 columns.

the code from mhttpd.c:show_status_page()
between
   /*---- run comment ----*/
and
   /*---- Equipment list ----*/
is attached

Dear experts,

I use fedora 12 and midas 4680. there is problem to start run when the frontend
application runs fine. 


# odbedit -c start


Starting run #18
[midas.c:8423:rpc_client_connect,ERROR] timeout on receive remote computer info: 
[midas.c:3659:cm_transition,ERROR] cannot connect to client
"feTPCPacketReceiver" on host tpcdaq0, port 36663, status 503
[midas.c:8423:rpc_client_connect,ERROR] timeout on receive remote computer info: 
[midas.c:4880:cm_shutdown,ERROR] Cannot connect to client 'frontend' on host
'hostname', port 36663
[midas.c:4883:cm_shutdown,ERROR] Killing and Deleting client
'feTPCPacketReceiver' pid 24516
[midas.c:3857:cm_transition,ERROR] Could not start a run: cm_transition() status
503, message 'Cannot connect to client 'frontend''
Run #18 start aborted
Error: Cannot connect to client 'frontend'

11:03:42 [Logger,INFO] Deleting previous file "/home/daq/Run/online/run00018.mid"

11:03:42 [Logger,INFO] Client 'feTPCPacketReceiver' on buffer 'SYSMSG' removed
by cm_watchdog because client pid 24516 does not exist

11:03:42 [Logger,ERROR] [system.c:563:ss_shm_close,ERROR]
shmctl(shmid=7274511,IPC_RMID) failed, errno 1 (Operation not permitted)

11:03:42 [ODBEdit,INFO] Run #18 start aborted
==========================================================================

there are several ethernet cards on the host machine. eth0 connect the host
machine to the gateway machine and the front end application listen to eth1 for
the incoming data packets:

eth0      Link encap:Ethernet  HWaddr xx:xx:xx:xx:xx:xx  
          inet addr:10.0.1.1  Bcast:10.0.1.63  Mask:255.255.255.0
          inet6 addr: fe80::f6ce:46ff:fe99:709b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:470870 errors:0 dropped:0 overruns:0 frame:0
          TX packets:515987 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:345000246 (329.0 MiB)  TX bytes:377269124 (359.7 MiB)
          Interrupt:17 

eth1      Link encap:Ethernet  HWaddr xx:xx:xx:xx:xx:xx   
          inet addr:10.0.1.2  Bcast:10.255.255.255  Mask:255.0.0.0
          inet6 addr: fe80::226:55ff:fed6:56a9/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:15 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:1836 (1.7 KiB)
          Memory:ec180000-ec1a0000 


thanks for hints

> - does your feTCPPacketReceiver die during the start-of-run? Maybe you do some segfault 
> int he begin-of-run routine. Can you STOP a run?
when start a run, it bring the mtransition process and I guess the server try to talk to the
client, then it fails and the frontend application get killed since not response.

>> When you try to stop your fe from 
> odbedit with  # odbedit -c "shutdown feTCPPacketReceiver"

it gets
[midas.c:8423:rpc_client_connect,ERROR] timeout on receive remote computer info: 
[midas.c:4880:cm_shutdown,ERROR] Cannot connect to client
"feTPCPacketReceiver" on host 'tpcdaq0', port 35865
[midas.c:4883:cm_shutdown,ERROR] Killing and Deleting client
'feTPCPacketReceiver' pid 27250
Client feTPCPacketReceiver not active


what does this error mean? :
11:03:42 [Logger,ERROR] [system.c:563:ss_shm_close,ERROR]
shmctl(shmid=7274511,IPC_RMID) failed, errno 1 (Operation not permitted)


thanks
hai

p.s. that code runs fine on my laptop with ubuntu 9, so that also be possible that somewhere
my configuration not right to cause problem

Hi all,

I am having some issues getting the ODBINC command to work within the MIDAS 
sequencer. I am trying to increment one of the ODB values but it is returning a 
mismatch data-type size error (see attached image).

All the ODB variables are MIDAS data-type FLOAT and should all be 32-bit values, 
but for some reason MIDAS is thinking they are 4-bit values. I have tried creating 
new ODB keys of type INT32, UINT32 and DOUBLE but they all give the same error.

If anybody has any suggestions I would really appreciate some help:)

Thanks



 

> Please post the output of odbedit "ls -l" for /eq/ar.../variables. (you posted the 
> variable name as an image, and I cannot cut-and-paste the odb path!). BTW data size 4 is 
> correct, 4 bytes for INT32/UINT32/FLOAT. For DOUBLE it should be 8. For you it prints 32 
> and this is wrong, we need to see the output of "ls -l".
> K.O.

Hi,

Thanks for getting back to me regarding this. The output of "ls -l" is:

[local:mu3eMSci:S]/>cd Equipment/ArduinoTestStation/Variables
[local:mu3eMSci:S]Variables>ls -l
Key name                        Type    #Val  Size  Last Opn Mode Value
---------------------------------------------------------------------------
_T_                             FLOAT   1     4     1h   0   RWD  20.93
_F_                             FLOAT   1     4     1h   0   RWD  12.8
_P_                             FLOAT   1     4     1h   0   RWD  56
_S_                             FLOAT   1     4     1h   0   RWD  5
_H_                             FLOAT   1     4     60h  0   RWD  44.74
_B_                             FLOAT   1     4     60h  0   RWD  18.54
_A_                             FLOAT   1     4     1h   0   RWD  14.41
_RH_                            FLOAT   1     4     1h   0   RWD  41.81
_AT_                            FLOAT   1     4     1h   0   RWD  20.46
SP                              INT16   1     2     1h   0   RWD  10

Many Thanks
Jago

> I tried following script:
> 
> ODBSET /Equipment/ArduinoTestStation/Variables/_S_, 10
> 
> LOOP 10
>   WAIT seconds, 3
>   ODBINC /Equipment/ArduinoTestStation/Variables/_S_
> ENDLOOP
> 
> and it worked as expected. So I conclude the problem must be in your script. Probably a typo in 
> the ODB path pointing to a 32-byte string instead to a 4-byte float.
> 
> Stefan  

Hi Stefan,

Cheers for the reply. I believe the syntax we are using is correct. I have tried copying the script 
you used above and it results in the same error as before. Perhaps something is going wrong 
elsewhere - I will take another look today.

Jago

> > 
> > [local:mu3eMSci:S]/>cd Equipment/ArduinoTestStation/Variables
> > [local:mu3eMSci:S]Variables>ls -l
> > Key name                        Type    #Val  Size  Last Opn Mode Value
> > ---------------------------------------------------------------------------
> > _T_                             FLOAT   1     4     1h   0   RWD  20.93
> > _F_                             FLOAT   1     4     1h   0   RWD  12.8
> > _P_                             FLOAT   1     4     1h   0   RWD  56
> > _S_                             FLOAT   1     4     1h   0   RWD  5
> > _H_                             FLOAT   1     4     60h  0   RWD  44.74
> > _B_                             FLOAT   1     4     60h  0   RWD  18.54
> > _A_                             FLOAT   1     4     1h   0   RWD  14.41
> > _RH_                            FLOAT   1     4     1h   0   RWD  41.81
> > _AT_                            FLOAT   1     4     1h   0   RWD  20.46
> > SP                              INT16   1     2     1h   0   RWD  10
> > 
> 
> This looks okey, so we still have no explanation for your error. Please post your sequencer 
> script?
> 
> K.O.

Hey, thanks for getting back to me

We are fairly confident the syntax is correct. Having tried the test script posted by Stefan:

> ODBSET /Equipment/ArduinoTestStation/Variables/_S_, 10
> 
> LOOP 10
>   WAIT seconds, 3
>   ODBINC 

The same error is returned:/

We will take another look today.

Jago

> Just post here a minimal script which produces the error, so that I can try myself.
> 
> ... and make sure that you have the latest develop version of midas.
> 
> Stefan

Here is the simplest script which produces the error:

WAIT seconds, 3
ODBINC /Equipment/ArduinoTestStation/Variables/_S_

I noticed that "Jacob Thorne"  in the forum had the same issue as us in Novemeber last 
year. Indeed we have not installed any later versions of MIDAS since then so we will 
double check we have the latest version.

Jago