Problem:
If cm_set_transition_sequence() is used for changing the sequence number, the 
command odbedit> start/stop/resume/pause -v report the propre sequence but the
action on the client side is actually not performed!

Fix:
Local transition table updated in midas.c (1.226)

Note:
The transition number under /system/clients/<pid>/transition...
is used internally. Changing it won't have any effect on the client action
if sequence number is not registered.

Hi Jan,

I usually keep under /Experiment/Run Parameters only those settings which are kind of "global" and thus of
interest to frontend *and* analyzer, like a run mode (data/calibration/cosmic/...). Settings more specific to a
frontend I keep under /Equipment/<name>/Settings where <name> is the equipment name the specific frontend
produces. In your case each frontend will then get its own tree (related to each fragment). Please note that
both discussed trees can contain a whole tree with subdirectories, which lets you organize your data better.

Best regards, Stefan.

I would like to know whether all parameters used by the frontend code have to be in the "Experiment/
Run Parameters" section.  This section can become big and difficult to maintain, because it is one single 
big section of experim.h (EXP_PARAM_DEFINED).  I have parameters the various frontends read at the 
beginning of each run, which set the hardware settings of various devices.  I would like to place these in 
a section all their own, organized by device.  Is this doable? 

Information about the Event Builder statistics has been removed from the 
Status page in mhttpd.  I heard from Pierre that this information might 
be redundant when using the new Event Builder format??? 
For the TWIST experiment, we are running and cannot change on the fly
to a new format Event Builder.  It is very important for us to show the users
the rates and statistics coming out of the EventBuilder.  I had  to put this
piece of code back in mhttpd.  
Can I put it back in the distribution? or do I have to put a special TWIST flag? 
or do I have to keep reinserting this every time there is an update to mhttpd.c? 
At the moment, TWIST is generating a couple of updates/week to mhttpd.c

I commited a fix to mhttpd logic that decides which messages should be shown in
"red" colour- before, any message with square brackets and colons would be
highlighted in red. Now only messages matching the pattern [...:...] are
highlighted. The decision logic was moved into a function message_red(). K.O.

> The upgrade of TWIST to the latest midas has bombed- we see mevb and mlogger
> crashes during shared memory data buffer accesses. I am looking into it and I
> will add information as I figure things out. K.O.

On second try, it looks like we are in business- the first try did not work
because of two mistakes:

1) I did not delete *all* old .SHM files (.ODB.SHM, .SYSTEM.SHM, .YBUF1.SHM,
.YBUF2.SHM). I deleted ODB.SHM, so odb worked, but forgot about the data buffers
SYSTEM.SHM & co and ended up with segmentation faults and core dumps in the buffer
management code caused by a mismatch of the old-midas buffers and new-midas code.
2) while debugging these core dumps, I made an error in my test code, so even
after I deleted the old data buffers, things still did not work. Talk about
over-debugging a problem...

K.O.

With latest midas, I see this:

Thu Oct 14 19:31:17 2004 [Lazy_Tape] [lazylogger.c:1717:Lazy] lazy_file_exists
file run17567.ybs doesn't exists
Thu Oct 14 19:31:27 2004 [Lazy_Tape] [lazylogger.c:1717:Lazy] lazy_file_exists
file run17567.ybs doesn't exists

The file run17567.ybs has size zero:

-rw-r--r--    1 twistonl users      950272 Oct 13 19:29
/twist/data_onl/current/run17565.ybs
-rw-r--r--    1 twistonl users      950272 Oct 13 19:45
/twist/data_onl/current/run17566.ybs
-rw-r--r--    1 twistonl users           0 Oct 13 20:00
/twist/data_onl/current/run17567.ybs
-rw-r--r--    1 twistonl users      983040 Oct 13 20:03
/twist/data_onl/current/run17568.ybs
-rw-r--r--    1 twistonl users      950272 Oct 13 20:26
/twist/data_onl/current/run17569.ybs

I am not sure how to fix this lazylogger logic. Please help.

K.O.

Agree.

Once you did the modification, please check following situation: Create a fresh
ODB withe increased size ("odbedit -s 2000000" for example). Then check that the
other clients "adopt" this increased size. Note that some experiments need a
bigger ODB, and I don't want to have them recompile all clients, that's why the
code in ss_shm_open() can attach to a *larger* shared memory. However, it should
not matter to the process, since the ODB (or SYSTEM) shared memory size is
stored in the pheader->key_size and pheader->data_size of each participating
process. So they should never write beyond the limits defined in that header.
The size to ss_shm_open() is only a "hint" if the shared memory does not exist,
and is nowhere later used in the code.

> > The upgrade of TWIST to the latest midas has bombed- we see mevb and mlogger
> > crashes during shared memory data buffer accesses. I am looking into it and I
> > will add information as I figure things out. K.O.
> 
> Since 1.9.5 the EventBuilder has been modified. Please consult the documentation
> where the new mevb scheme is explained.
> Test of the mevb with up to 16 frontends (15 different CPUs) has been tested
> successfully. Data rate at the EventBuilder were measured about 50MB/s without the
> logger and ~30MB/s with the logger.

It turns out that TWIST uses a private mevb.c. We will consider upgrading to the
standard one.

K.O.

> The upgrade of TWIST to the latest midas has bombed- we see mevb and mlogger
> crashes during shared memory data buffer accesses. I am looking into it and I
> will add information as I figure things out. K.O.

I traced buffer memory corruption to a logic error in system.c::ss_shm_open(). If
a .SHM file exists, it's size is used as the size of the sysv shared memory
segment, even if the requested shared memory size is bigger, but the caller of
ss_shm_open()  thinks it got all the requested memory. Eventually we try to use
the unallocated memory and crash. This is the proposed fix and I will commit it
after I retest the upgrade during the next few days.

[olchansk@send src]$ cvs diff -u system.c
olchansk@midas.psi.ch's password: 
Index: system.c
===================================================================
RCS file: /usr/local/cvsroot/midas/src/system.c,v
retrieving revision 1.83
diff -u -r1.83 system.c
--- system.c    4 Oct 2004 07:04:01 -0000       1.83
+++ system.c    14 Oct 2004 05:51:16 -0000
@@ -544,8 +544,14 @@
       } else {
          /* if file exists, retrieve its size */
          file_size = (INT) ss_file_size(file_name);
-         if (file_size > 0)
+         if (file_size > 0) {
+            if (file_size < size) {
+               cm_msg(MERROR, "ss_shm_open", "Shared memory segment \'%s\' size
%d is smaller than requested size %d. Please remove it and try
again",file_name,file_size,size);
+               return SS_NO_MEMORY;
+            }
+            
             size = file_size;
+         }
       }
 
       /* get the shared memory, create if not existing */

K.O.

> The upgrade of TWIST to the latest midas has bombed- we see mevb and mlogger
> crashes during shared memory data buffer accesses. I am looking into it and I
> will add information as I figure things out. K.O.

Since 1.9.5 the EventBuilder has been modified. Please consult the documentation
where the new mevb scheme is explained.
Test of the mevb with up to 16 frontends (15 different CPUs) has been tested
successfully. Data rate at the EventBuilder were measured about 50MB/s without the
logger and ~30MB/s with the logger.

The upgrade of TWIST to the latest midas has bombed- we see mevb and mlogger
crashes during shared memory data buffer accesses. I am looking into it and I
will add information as I figure things out. K.O.

> > We have al_trigger_alarm(), but no matching al_clear_alarm(), and I need it to
> > clear my alarm once the alarm condition no longer exists. Any objections if I
> > add this function? K.O.
> 
> call al_reset_alarm()

Thanks. I must be quite blind as I did not see al_reset_alarm() in midas.h. I se eit
now. Thanks.

K.O.

> We have al_trigger_alarm(), but no matching al_clear_alarm(), and I need it to
> clear my alarm once the alarm condition no longer exists. Any objections if I
> add this function? K.O.

The idea is that once an alarm got triggered, it stays until the user
acknowledged, even if the alarm condition has been disappeared. Through mhttpd,
the user can press the "Reset" button, which then executes al_reset_alarm().
However, it is possible to call al_reset_alarm() directly from user code to
achieve the same thing.

We have al_trigger_alarm(), but no matching al_clear_alarm(), and I need it to
clear my alarm once the alarm condition no longer exists. Any objections if I
add this function? K.O.

> odbedit command "rename Display xxx/yyy" creates a key named "xxx/yyy" (yes,
> with a slash in the name) and this key cannot be deleted or renamed...
> K.O.

"rename" is "rename", not "mv" under Unix. If you want this functionality, put it
in and don't complain!

odbedit command "rename Display xxx/yyy" creates a key named "xxx/yyy" (yes,
with a slash in the name) and this key cannot be deleted or renamed...
K.O.

Can you attach 

/twist/data_onl/current/run17548.odb

so I can reproduce the problem?

I am updating TWIST to the latest MIDAS and when I load a saved .odb file, I get
these messages. Their text ought to say where and what strings it does not like.
K.O.



[twistonl@midtwist ~/online]$ odbedit
Please define environment variable 'MIDASSYS'
pointing to the midas installation directory.
[local:twist:S]/>load /twist/data_onl/current/run17548.odb
[odb.c:5600:db_paste] found string exceeding MAX_STRING_LENGTH
[odb.c:5600:db_paste] found string exceeding MAX_STRING_LENGTH
[odb.c:5600:db_paste] found string exceeding MAX_STRING_LENGTH

>    A lot of programs have a commandline option, such as "--version", where they return the program version number then exit.  As well as the
> program version number, the version number of the midas library it's linked with could also be returned (There can be more than one
> libmidas.so on a system and this would show which one was currently being linked)

This would solve the versioning problem for midas built from versionned tarballs, and I am considering a similar scheme for midas installed from
RPMs. But what do I do for midas built from CVS?!? K.O.