BNMR: Custom Status page

• BNMR overview
• Getting started
• Troubleshooting
• All BNMR pages
• Midas

Links

• BNMR
• Experimental Modes
• Getting Started
• Custom Parameters page
• Nomenclature

Introduction

When the webserver is used to connect to a MIDAS experiment, the standard MIDAS Status page is shown, unless it has been replaced by a Custom Status page. This is the case for the bnmr and bnqr experiments. A custom page written specifically for the bnmr and bnqr experiments replaces the standard MIDAS Status page. It is called the Custom Status page.

Note that the MIDAS client mhttpd must be running for the webserver to be available. To connect to the Custom Status page, see Getting Started.

Custom Status Page

The custom status page allows users to enter experimental parameters easily, including changing Experimental Modes and run type. A Custom Parameter page accessed from the custom status page allows users to enter run parameters easily. The custom status page for bnmr and bnqr experiments is shown in Figures 1 and 2 respectively.

Figure 1 BNMR Custom Status Page (Run Stopped)

File:Bnmr status stopped.png

Figure 2 BNQR Custom Status Page (Run Stopped)

File:Bnqr status stopped.png

Features of the Custom Status Page

The Custom Status Page provides status information specific to the bnmr or bnqr experiments. The option of reverting to the MIDAS standard status page is provided via the ToggleStatusPage button.

Command and Page Buttons

Figure 3 Command and Page Buttons
In the middle of the top line on the Custom Status page are found the standard Menu buttons to stop and start runs or to display different MIDAS pages. These standard buttons appear on most MIDAS pages (see MIDAS Status page for more information).

Below these buttons are buttons specific to the bnmr and bnqr experiment. Some are customscript buttons, that is, a script is run when the button is pressed. Others switch to a different custom page. The actions of these buttons are described in Table 1.

Table 1: Custom Buttons

Button	Action
Autorun	toggles Autoruns on or off
rf_config	runs client rf_config to test the validity of the input parameters without actually starting a run
ToggleStatusPage	runs a perlscript causing the status page to revert to the standard Midas Status Page. After pressing this button, a popup window with a message "Now refresh page" will appear. After refreshing the page, the MIDAS status page will appear. From this page, the CustomStatus page can be reached by clicking on the custom button CustomStatus button. This will show the Custom status page as a regular Custom page. A message can be seen at the top of the custom page in this case "Using alias link "CustomStatus&" from Midas Main Status Page". To revert to running this page as the Custom Status Page, press the button once more and refresh the page.
RunParams	gives access to the Custom Parameter page.
ShowWindows	button displays the help information on displaying the frontend and other client consoles.

Page Update Information

The page update information is also visible in Figure 1. The custom status page updates completely with a full page reload every minute. In between, it updates the information using innerHTML. This is called a partial reload. The time between partial reloads can be set by the user by clicking on the link "Page update 10 sec (min 5s)" (Figure 1). This minimum time is 5s. The ODB data is read each time a partial reload is done. The times of the last ODB data read, last full reload etc are also shown in Figure 1. A countdown to the next full reload is also visible.

Status Line

The Status lines on the Custom Status Page show the status of the run and some of the important settings (Figure 4).

Figure 4 Status lines from the BNQR Custom Status Page

File:Bnqr status lines.png
The first line shows the selected PPG Mode. This changes when the mode is changed by pressing one of the PPG Mode buttons. The run number (Table 2) is shown in different colours for a test or real run (see BNMR: Run numbering).

Table 2: Run number	spacer	Table 3: Run State
Run number 45059 real 30102 test	spacer	Run Status Stopped On Hold Running

The run state is shown in different colours depending on the run state (Table 3). The time the run started is shown and, if running, the run duration, otherwise the time the run stopped. The next line shows the Status, which may show an information message. Below this is a line showing the directory of the saved files.

Next are a number of boxes showing important settings (Table 4). Most are provided with a checkbox so the user can change the values from the custom status page.

Table 4 Status values

Status boxes

Parameter TRUE	Parameter FALSE	Checkbox
Single channel mode	Dual channel mode	yes
Alarms Active	Alarms Active	yes
Helicity Check	Helicty Check	yes
Helicity Flip	Helicity Flip	no
Single/Dual Mode Switch Check	Single/Dual Mode Switch Check	yes

NOTE

When real data is being taken (i.e. the run mode is set to real ), this line should

look similar to Figure 4, with Alarms Active, Helicity Check, Helicity Flip and Single/Dual Mode Switch Check all being enabled.

Select PPG and Run Mode

This line on the Custom Status Page contains the PPG Mode change and Run Mode buttons (Figure 5).

Figure 5 PPG and Run Mode switch buttons

File:Bnqr select mode line.png
These buttons are only visible when the run is stopped. The user selects the desired PPG Mode by pressing one of the PPG Mode buttons. The buttons will then be replaced by a message as in Figure 6.

Figure 6 PPG Mode changing

File:Bnmr ppg mode changing.png

After a short time, the PPG Mode will change to the selected mode and the PPG Mode buttons will reappear. The Custom Parameters page can be viewed by pressing the PPG Mode button again.

The PPG Mode buttons are customscript buttons which call the perlscript change_mode.pl. The perlscript may take a few seconds to run, so a message is displayed to prevent the impatient user from clicking more buttons.

This line also contains the Run Mode buttons TEST and REAL. The coloured (non-grey) button indicates whether the run mode is currently TEST or REAL. The buttons are only visible when the run is stopped. When running, they are replaced by TOGGLE for Type 2 runs only. For Type 1 runs, they are replaced by a message.

If the run type is REAL as in Figure 5, and the TEST button is pressed, a message will appear (Figure 7), then the run type will change to TEST (Figure 8).

Figure 7 Run Mode is changing	spacer	Figure 8 Run Mode has changed
File:Bnmr run mode changing1.png	spacer	File:Bnmr run mode changing.png

The PPG Mode buttons are customscript buttons which call the perlscripts real_run.pl or test_run.pl The perlscript may take a few seconds to run, so a message is displayed to prevent the impatient user from clicking more buttons.

Programming Information

See Custom Pages.