One can collapse the side panel when looking at history pages with the button in
the top left, great! We want to see many pages so screen real estate is important

The issue we face is that when the page refreshes, the side panel expands. Can
we make the panel state more 'sticky'?

Many thanks
Joseph (ALPHA)

Version: 	2.1
Revision: 	Mon Mar 19 18:15:51 2018 -0700 - midas-2017-07-c-197-g61fbcd43-dirty
on branch feature/midas-2017-10

Hi all

There is a bug report in the ROME repository which says bm_receive_event timeouts.

https://bitbucket.org/muegamma/rome3/issues/8/rome-with-midas-produces-timeout-after

Does anybody have any ideas what could causing the problem ?

Ryu

> > Hello Everybody,
> > 
> > I am a member of a satellite team with a scientific payload and I am considering
> > coordinating the payload using MIDAS. This looks to be challenging since MIDAS
> > would be implemented on an Xilinx Spartan 6 FPGA with minimal hardware
> > resources. The idea would be to install a soft processor on the Spartan 6 and
> > run MIDAS through UCLinux either on the FPGA or boot it from SPI Flash. Does
> > anybody have any comments on how feasible this would be or perhaps have
> > experience implementing a similar system?
> > 
> > -Devin
> 
> While some people successfully implemented a midas *client* in an FPGA softcore, the full midas 
> backend would probably not fit into a Spartan 6. Having done some FPGA programming and 
> working on satellites, I doubt that midas would be well suited for such an environment. It's 
> probably some kind of overkill. The complete GUI is likely useless since you want to minimize your 
> communication load on the satellite link.
> 
> Stefan

Thank you for your comment Stefan. We do have some hardware resources on the board such as RAM, ROM and
Flash storage so we wouldn't necessarily have to virtualize everything. Ideally we would like a
completed and compressed file to be produced on board and regularly sent back to ground without
requiring remote access. MIDAS is appealing to us because its easily automated but we wouldn't
necessarily need functions like a GUI or web interface. Part of the discussion now is whether or not a
microblaze processor would be sufficient or if we need a dedicted ARM processor.

Devin 

> Hello Everybody,
> 
> I am a member of a satellite team with a scientific payload and I am considering
> coordinating the payload using MIDAS. This looks to be challenging since MIDAS
> would be implemented on an Xilinx Spartan 6 FPGA with minimal hardware
> resources. The idea would be to install a soft processor on the Spartan 6 and
> run MIDAS through UCLinux either on the FPGA or boot it from SPI Flash. Does
> anybody have any comments on how feasible this would be or perhaps have
> experience implementing a similar system?
> 
> -Devin

While some people successfully implemented a midas *client* in an FPGA softcore, the full midas 
backend would probably not fit into a Spartan 6. Having done some FPGA programming and 
working on satellites, I doubt that midas would be well suited for such an environment. It's 
probably some kind of overkill. The complete GUI is likely useless since you want to minimize your 
communication load on the satellite link.

Stefan

> I was planning to use the alarm system to display an information banner when a
> certain valve is open, but I would like it to go away again when the valve is
> closed.
> Is there a way to achieve that? Maybe reset the alarm from an alarm script?
> (Seems like a hack...)
> Maybe this could be a useful feature, to be able to define an alarm class that
> resets itself once the condition is no longer met?

Actually you can implement such a thing already now pretty quickly using custom javascript on 
the status page. Just read the valve state regularly from the ODB and dynamically modify the 
status page to show or hide a banner. Look how custom pages work in midas and try to apply 
this to the status page status.html which you find in the resources directory.

Stefan

> If you run an external script anyway, you can also call "odbedit -c alarm" to
> reset all alarms. Or you could try to set the "Triggered" entry of that certain
> alarm to 0 (again, with odbedit), that could also work.

That would not really help, because you cannot trigger a script AFTER an alarm occurred. Having 
"self-resetting" alarms is actually not a bad idea. I could add a flag "Auto reset" which is false by 
default and can be set to true for this functionality. Will keep that in mind for the next 
development cycle.

Stefan

If you run an external script anyway, you can also call "odbedit -c alarm" to
reset all alarms. Or you could try to set the "Triggered" entry of that certain
alarm to 0 (again, with odbedit), that could also work.

I was planning to use the alarm system to display an information banner when a
certain valve is open, but I would like it to go away again when the valve is
closed.
Is there a way to achieve that? Maybe reset the alarm from an alarm script?
(Seems like a hack...)
Maybe this could be a useful feature, to be able to define an alarm class that
resets itself once the condition is no longer met?

Hello Everybody,

I am a member of a satellite team with a scientific payload and I am considering
coordinating the payload using MIDAS. This looks to be challenging since MIDAS
would be implemented on an Xilinx Spartan 6 FPGA with minimal hardware
resources. The idea would be to install a soft processor on the Spartan 6 and
run MIDAS through UCLinux either on the FPGA or boot it from SPI Flash. Does
anybody have any comments on how feasible this would be or perhaps have
experience implementing a similar system?

-Devin

> > Dear experts,
> >               is there any way to launch an executable script on the host computer from the MIDAS 
> > sequencer? If not, is there any interest to develop such a feature?
> > 
> > Thank you,
> >          Francesco
> 
> The SCRIPT command will do that (on the machine running MIDAS). I know it works with either python or
> bash scripts. I tried without success to pass the parameters and I went around by setting ODB entries
> prior to running the script and then access to them within the script.

Passing parameters should work. If it's confirmed to be broken, I'm willing to fix it.

Stefan

> Dear experts,
>               is there any way to launch an executable script on the host computer from the MIDAS 
> sequencer? If not, is there any interest to develop such a feature?
> 
> Thank you,
>          Francesco

The SCRIPT command will do that (on the machine running MIDAS). I know it works with either python or
bash scripts. I tried without success to pass the parameters and I went around by setting ODB entries
prior to running the script and then access to them within the script.

Dear experts,
              is there any way to launch an executable script on the host computer from the MIDAS 
sequencer? If not, is there any interest to develop such a feature?

Thank you,
         Francesco

> > Asume you have a variable foo and a link bar -> foo. When you go to the ODB in
> > mhttpd, click "Delete" and select bar, it actually deletes foo. bar stays,
> > stating "<cannot resolve link>". Trying the same in odbedit with rm gives the
> > expected result (bar is gone, foo is still there).
> > 
> > I'm on the develop branch.
> 
> I think I can confirm this. Created a bug report on bitbucket:
> 
> https://bitbucket.org/tmidas/midas/issues/148/mhttpd-odb-editor-deletes-wrong-symlink
> 
> K.O.

I fixed this and committed the change. Took me a while since it was in KO's code.

Stefan

Per changes at TRIUMF, the MIDAS forum mail relay was changed from trmail.triumf.ca to 
smtp.triumf.ca. K.O.

> Hi. We've just updated our midas installation to the newest version, and we now see repeated errors from the 
> mserver in messages. Mostly we see
> 
> 11:17:02.994 2018/08/21 [ODBEdit,TALK] Program mserver restarted
> 
> which happens 2-3 times per minute. 
> 
> We have also been seeing occasional dropped rpc connections to our frontends, which could be related. 
> 
> The version we were running with previously was ~1 year old, and we have just updated to the newest version 
> on bitbucket. 

Hmm... usually mserver will not restart automatically, maybe you have set it to autorestart on ODB (/programs/mserver/auto_restart 
set to "y").

It would be unusual for the main mserver program to crash, to debug it, you will need to run it in a terminal
and see if there is any error messages. Even better to run it in a terminal inside "gdb" and capture the stack trace
when it crashes.

Anyhow, crash of main mserver will not cause "dropped rpc connections" to clients - this would require for their
individual mserver subprocesses to crash. Such crashes would be highly unusual and are harder to debug.

Perhaps for the crashes you see there is some error messages in midas.log?

K.O.

> I would like to store the address of 1-Wire temperature sensors in a device
> driver. However, the supportet data types (as definded around
> include/midas.h:311) do not foresee a type large enough.
>

Hmm... you do not say what sensor you use and how many bits you actually need.

For up to 32 bits you can use TID_DWORD (uint32_t) (obviously)

For up to 48 bits (or so), you can use TID_DOUBLE (double) (wierd, but IEEE754 double precision variables would work as 48-bit (or so) integers).

For more, I would use arrays of TID_DWORD (64 bits, store low 32 bits into a[0], high bits into a[1]).

> 
> Is there a good reason against this?
> 

We had requests for implementing uint64_t 64-bit data types in MIDAS before. There are two problems:

a) in the MIDAS data banks, there is a problem with the bank header definition which only has 3 DWORDSs so causes
each alternating data bank to be 64-bit misaligned. And misaligned 64-bit data is very bad.

b) in ODB, 64-bit data support will need to be added from scratch and again it is not clear without doing it
if there will be any alignement problems. If one were to implement ODB from scratch, one would have everything
aligned to 64-bits or maybe even 128-bits, with uint64_t fully supported.

It is unlikely this kind of work will ever be done on ODB, but who knows.

> I know that other experiments use this kind of sensor, how do you store the
> addresses? I've noticed that most of the address is just zeroes, but I wouldn't
> like to store just half the address, assuming that half the address is always
> zeroes.

Cannot answer without knowing what sensor you use, but certainly you can use an array of bytes
or an array of integers to store arbitrarily long addresses. You can also use a TID_STRING
and store the address as a text string "0xabcdabcdabcdabcd" of arbitrary length.

K.O.

Hi, what you try should have worked. Perhaps your symlink is wrong and should say "/External/..." (with a leading slash). The "links period" would have
worked same as equipment/common/history period - as a rate limiter.

Anyhow, I suggest another way to do the same - create a fake equipment - the logger does
not care if the equipment is real or not and if you write into /eq/fake/variables from a proper frontend
or from a script. To hide the fake equipment from the status page, set /eq/fake/common/hidden to "true".

This will work for sure.

K.O.




> Hi,
> I am trying to set up virtual history events following
> https://midas.triumf.ca/MidasWiki/index.php/History_System#Virtual_History_Event 
> 
> Trying it the first way, using the following setup:
> Key name                        Type    #Val  Size  Last Opn Mode Value
> ---------------------------------------------------------------------------
> Links                           DIR
>     dirlink -> External/dir     KEY     1     12    >99d 0   RWD  <subdirectory>
> 
> 
> Key name                        Type    #Val  Size  Last Opn Mode Value
> ---------------------------------------------------------------------------
> External                        DIR
>     dir                         DIR
>         foo                     FLOAT   1     4     16s  0   RWD  12.5
> 
> 
> Then I get the following error message:
> ==================== History link "dirlink", ID 28150  =======================
> [Logger,ERROR] [mlogger.cxx:4942:open_history,ERROR] History event dirlink has
> no variables in ODB
> 
> 
> Trying the second way, I set up the following:
> Key name                        Type    #Val  Size  Last Opn Mode Value
> ---------------------------------------------------------------------------
> Links                           DIR
>     dir                         DIR
>         testlink -> External/foo
>                                 FLOAT   1     4     8m   0   RWD  5.2
> 
> Key name                        Type    #Val  Size  Last Opn Mode Value
> ---------------------------------------------------------------------------
> External                        DIR
>     foo                         FLOAT   1     4     6m   0   RWD  5.2
> 
> 
> Starting mlogger in verbose mode yields the following error:
> ==================== History link "dir", ID 28150  =======================
> [Logger,ERROR] [mlogger.cxx:4935:open_history,ERROR] History link
> /History/Links/dir/testlink is invalid
> Error in history system, aborting startup.
> 
> I'm not sure if this is a bug or just a case of PEBCAK.
> 
> Finally, to set the update period, do I need entries in /history/links periods
> with the tag name? Is there a way to only write them in the history file when
> they change? I want to use the virtual history events for measurements I get
> from external scripts, some periodic, some manual.
> 
> Thanks

> Asume you have a variable foo and a link bar -> foo. When you go to the ODB in
> mhttpd, click "Delete" and select bar, it actually deletes foo. bar stays,
> stating "<cannot resolve link>". Trying the same in odbedit with rm gives the
> expected result (bar is gone, foo is still there).
> 
> I'm on the develop branch.

I think I can confirm this. Created a bug report on bitbucket:

https://bitbucket.org/tmidas/midas/issues/148/mhttpd-odb-editor-deletes-wrong-symlink

K.O.

Hi,
I am trying to set up virtual history events following
https://midas.triumf.ca/MidasWiki/index.php/History_System#Virtual_History_Event 

Trying it the first way, using the following setup:
Key name                        Type    #Val  Size  Last Opn Mode Value
---------------------------------------------------------------------------
Links                           DIR
    dirlink -> External/dir     KEY     1     12    >99d 0   RWD  <subdirectory>


Key name                        Type    #Val  Size  Last Opn Mode Value
---------------------------------------------------------------------------
External                        DIR
    dir                         DIR
        foo                     FLOAT   1     4     16s  0   RWD  12.5


Then I get the following error message:
==================== History link "dirlink", ID 28150  =======================
[Logger,ERROR] [mlogger.cxx:4942:open_history,ERROR] History event dirlink has
no variables in ODB


Trying the second way, I set up the following:
Key name                        Type    #Val  Size  Last Opn Mode Value
---------------------------------------------------------------------------
Links                           DIR
    dir                         DIR
        testlink -> External/foo
                                FLOAT   1     4     8m   0   RWD  5.2

Key name                        Type    #Val  Size  Last Opn Mode Value
---------------------------------------------------------------------------
External                        DIR
    foo                         FLOAT   1     4     6m   0   RWD  5.2


Starting mlogger in verbose mode yields the following error:
==================== History link "dir", ID 28150  =======================
[Logger,ERROR] [mlogger.cxx:4935:open_history,ERROR] History link
/History/Links/dir/testlink is invalid
Error in history system, aborting startup.

I'm not sure if this is a bug or just a case of PEBCAK.

Finally, to set the update period, do I need entries in /history/links periods
with the tag name? Is there a way to only write them in the history file when
they change? I want to use the virtual history events for measurements I get
from external scripts, some periodic, some manual.

Thanks

Asume you have a variable foo and a link bar -> foo. When you go to the ODB in
mhttpd, click "Delete" and select bar, it actually deletes foo. bar stays,
stating "<cannot resolve link>". Trying the same in odbedit with rm gives the
expected result (bar is gone, foo is still there).

I'm on the develop branch.