Hi All,

I've installed midas (Rev:5294) on SLC6.3 (64bit), along with recent trunk versions of rootana and roody. 
All the packages compiled OK. The example code in $MIDASSYS/examples/experiment also runs OK 
provided that I don't launch roody. If I try to launch roody, then it immediately crashes the analyzer with 
the following trace:

#6 root_server_thread (arg=ox7f54fc001150) at src/mana.c:5154
#7 0x0000003219a1e13a in TThread::Function(void*) () from /usr/lib64/root/libThread.so.5.28
#8 0x0000003dd1207851 in start_thread () from /lib64/libpthread.so.0
#9 0x0000003dd0ee76dd in clone () from /lib64/libc.so.6

The line src/mana.c:5154 points to the following:

TObject *obj;
            if (strncmp(request + 10, "Any", 3) == 0)
               obj = folder->FindObjectAny(request + 14);
            else
               obj = folder->FindObject(request + 11);    // LINE 5154


Any suggestions on what may be going on here?  Thanks.


Cheng-Ju

OK, I've found the solution in the roody forum.  The solution for 64bit machine is to replace
   uint32_t p =0;
   with
   uintptr_t p =0;

in the roody header file roody/include/DataSourceTNetFolder.h

Cheng-Ju



> Hi All,
> 
> I've installed midas (Rev:5294) on SLC6.3 (64bit), along with recent trunk versions of rootana and roody. 
> All the packages compiled OK. The example code in $MIDASSYS/examples/experiment also runs OK 
> provided that I don't launch roody. If I try to launch roody, then it immediately crashes the analyzer with 
> the following trace:
> 
> #6 root_server_thread (arg=ox7f54fc001150) at src/mana.c:5154
> #7 0x0000003219a1e13a in TThread::Function(void*) () from /usr/lib64/root/libThread.so.5.28
> #8 0x0000003dd1207851 in start_thread () from /lib64/libpthread.so.0
> #9 0x0000003dd0ee76dd in clone () from /lib64/libc.so.6
> 
> The line src/mana.c:5154 points to the following:
> 
> TObject *obj;
>             if (strncmp(request + 10, "Any", 3) == 0)
>                obj = folder->FindObjectAny(request + 14);
>             else
>                obj = folder->FindObject(request + 11);    // LINE 5154
> 
> 
> Any suggestions on what may be going on here?  Thanks.
> 
> 
> Cheng-Ju

Hi Konstantin,

Many thanks for your feedback.  I was able to keep the analyzer from exiting when launching roody by making some changes in the roody code. 
This at least allows me to keep moving forward. I will look into your suggestion of converting to ROOTANA based analyzer as well.

Regards,

Cheng-Ju


> > I've installed midas (Rev:5294) on SLC6.3 (64bit), along with recent trunk versions of rootana and roody. 
> >
> > #6 root_server_thread (arg=ox7f54fc001150) at src/mana.c:5154
> 
> You are connecting to mana, the old midas analyzer. The code for connecting to it is still present in roody,
> but I cannot support the matching server code in mana.c - it is 2 revolutions behind the current state of
> the ROOT object server (look in ROOTANA - the NetDirectory stuff and the latest is the XmlServer stuff).
> 
> I can offer 2 solutions - switch from mana.c to a ROOTANA based analyzer or graft the XmlServer code
> into your analyzer (it is very simple - you need to create an XmlServer object and tell it which ROOT
> containers you want to make visible to ROODY).
> 
> I guess you can also debug the old midas server code inside mana.c...
> 
> K.O.

Hi

I'm not sure if this is the right forum for this query (if it is not, I would truly appreciate it if someone could point me at the right forum). I'm having a little bit of trouble with the setup of a Midas system.

Now, this is a system that I inherited after the previous guy who was looking after it went to other employment. There was a point at which it was working. And then there was an unrelated issue in the electrical system which, as a side effect, meant that the building lost power for a time, and the entire system had to be rebooted.

No problem, I thought. I'll just reset and restart all of the software...

...and I can't seem to get it to work. I keep getting the error message "mvme_read_value: Could not perform read!: Bad address". So far as I can tell, this seems to be related to the idea that the base address being used to read from the boards is incorrect. The base addresses are hardcoded in the software (not autogenerated) and, aside from the power going down and up again, the hardware hasn't been touched since the system was working.

I imagine that there is something that needs to be set, twiddled, tweaked, or turned on in the driver. The output of 'lsmod | grep vme' is:

vmedriver             117742  0

so presumably the driver is at least *present*, even if I have no idea how to twiddle anything on it.

Could anyone perhaps suggest a way forward? Is there some way to gather the information that I need, perhaps, or some way to twiddle anything twiddle-able on the driver?

Casey

Hi,
   has anyone managed to get midas to work on a x86_64 processor. I followed the
instructions for the 64-bit opteron but i am getting runtime error when trying
the examples.

 When running example/basic/odb_test I getting errors like

[odb.c:6818:db_get_record] struct size mismatch for "/Alarms/Alarms/Demo ODB"
(464 instead of 452)
[odb.c:6818:db_get_record] struct size mismatch for "/Alarms/Alarms/Demo ODB"
(464 instead of 452)
[midas.c:16576:al_check] Cannot get alarm record

Any ideas what is wrong?

I upgraded from 1.9.5 to the latest on SVN an it works fine

Hi,
   the system I'm building will have data read into the frontend nodes
via ethernet (optic). Is this possible?>

Hi,
   I'm setting up a system with two networks with the intension of having
control info (odb, alarm) on the 192.168.0.x
and the frontend readout on 192.168.1.x

Is there any easy way of doing this?
I'm also trying to separate processes onto different machines, is there
any way to not have mserver,mhttpd and (mlogger,mevt) all run on the same
machine?
Thanks,
       Carl Metelko

Hi,
   thanks for the advice. We do have dual core Xeons so we'll try running
most things on the server. Unless it proves to be a problem we'll run all
MIDAS signals on one network and NFS etc on the other.

I do have one more query about running systems like Konstantin.
What we would like to do is have a 'mirror' server serving multiple
online monitoring machines so that the load on the server is constant nomatter
the demands on the mirror.

Is there a way to set this up? Or would it be best to have a remote analyser
making short (1min) root files shared with the online monitoring? 

Hi,
    I found that midas banks can be given an extra 32 bits of zeros when
trying to keep to 32bit boundary on my x86_64. 

This can be fixed by changing (in midas.h)
#define ALIGN8(x)  (((x)+7) & ~7)
to
#define ALIGN8(x)  (((x)+3) & ~3)

Is there any bad consequences doing this?

Hello all,

I am trying to put together a system to read out several camac adc. The camac is
read by a ces8210 camac to vme controller. The vme is then interfaced to a
computer through a CAEN v1718 usb control module. As anyone gotten the latter to
work?

Previous users seemed to indicate that they had here:

https://ladd00.triumf.ca/elog/Midas/493

but I am having problems to get this example frontend to compile. What is set as
the driver in the makefile for example? If I put v1718 there then I recieve
numerous errors from the CAENVMElib files. 

If someone else has gotten the V1718 running, I would be grateful for their
insight. 

Thanks, 
-Carl

Dear MIDAS programmers,

I have been using your software in my lab (APC, Paris)
to run our data acqusition system. It is very robust and flexible.s

I would like to give you the large amount of credit which you are due.
How should I cite both MIDAS and ROODY? I have not been able to find any
information in the usual places.

Cheers, and thanks for the great program!
-Carl

Hello,

At our lab we are currently in the process of migrating more of our systems over to Midas. However, all of our working systems are dependent on SBCs with the Tsi-148 chips of which we only have a handful. In order to have some backups and spares for testing, we have been attempting to get Midas working with some borrowed SBCs (Concurrent Technologies VX 40x/04x) with Universe-II chips. The SBC is running CentOS 7. I have tried to follow the instructions posted here. The universe-II kernel module appears to load correctly, dmesg gives:

[   32.384826] VME: Board is system controller
[   32.384875] VME: Driver compiled for SMP system
[   32.384877] VME: Installed VME Universe module version: 3.6.KO6
 

However, running vmescan.exe fails with a segfault. Running with gdb shows:

vmic_mmap: Mapped VME AM 0x0d addr 0x00000000 size 0x00ffffff at address 0x80a01000
mvme_open:
Bus handle              = 0x7
DMA handle              = 0x6045d0
DMA area size           = 1048576 bytes
DMA    physical address = 0x7ffff7eea000
vmic_mmap: Mapped VME AM 0x2d addr 0x00000000 size 0x0000ffff at address 0x86ff0000

Program received signal SIGSEGV, Segmentation fault.
mvme_read_value (mvme=0x604010, vme_addr=<optimized out>)
    at /home/jam/midas/packages/midas/drivers/vme/vmic/vmicvme.c:352
352        dst  = *((WORD *)addr);
 

With the pointer addr originating from a call to vmic_mapcheck within the  mvme_read_value functions in the vmicvme.c file. Help with where to go from here would be appreciated.

-Caleb 

Here is the output:

vmic_mmap: Mapped VME AM 0x0d addr 0x00000000 size 0x00ffffff at address 0x80a01000
mvme_open:
Bus handle              = 0x3
DMA handle              = 0x158f5d0
DMA area size           = 1048576 bytes
DMA    physical address = 0x7f91db553000
vmic_mmap: Mapped VME AM 0x2d addr 0x00000000 size 0x0000ffff at address 0x86ff0000
vme addr: 00000000 
addr: db543000 

I am looking into compiling the 32 bit midas.

In the meantime, here is the kernel info:

3.10.0-1160.11.1.el7.x86_64 

Thank you for the help.
-Caleb

I can compile 32 bit midas. Unless I am interpreting the linking error, I don't 
think I can use the driver as built. 

While trying to compile vme_scan, most of the programs fail with:

/usr/bin/ld: skipping incompatible /usr/lib/gcc/x86_64-redhat-
linux/4.8.5/../../../../lib/libvme.so when searching for -lvme
/usr/bin/ld: skipping incompatible /lib/../lib/libvme.so when searching for -lvme
/usr/bin/ld: skipping incompatible /usr/lib/../lib/libvme.so when searching for -
lvme
/usr/bin/ld: skipping incompatible /usr/lib/gcc/x86_64-redhat-
linux/4.8.5/../../../libvme.so when searching for -lvme
/usr/bin/ld: skipping incompatible //lib/libvme.so when searching for -lvme
/usr/bin/ld: skipping incompatible //usr/lib/libvme.so when searching for -lvme

with libvme.so being built by the universe-II driver. Not sure if I can get around 
this without messing with the driver? Is it possible to build a 32 bit version of 
that shared library without having to touch the actual kernel module? 

-Caleb

Hi all, 

I have a Mac with OS 10.13.6 and Xcode 10.1. I am following the instructions in the wiki to install Midas. 
I have installed openssl via MacPorts as per the instructions. But then I get an error related to open ssl 
when I try to compile Midas. See the results of cmake .. and make install 

Darrens-Mac-mini:build betacage$ cmake ..
-- MIDAS: cmake version: 3.16.3
-- MIDAS: CMAKE_INSTALL_PREFIX: /Users/betacage/packages/midas
-- MIDAS: Found ROOT version 6.18/04
-- MIDAS: Found ZLIB version 1.2.11
-- MIDAS: Found OpenSSL version 1.1.1d
-- MIDAS: MySQL not found
-- MIDAS: ODBC not found
-- MIDAS: Found SQLITE /usr/include/sqlite3.h
-- MIDAS: nvidia-smi not found
-- MIDAS example/experiment: MIDAS in-tree-build
-- MIDAS: Found ZLIB version 1.2.11
-- MIDAS example/experiment: Found ROOT version 6.18/04
-- Configuring done
-- Generating done
-- Build files have been written to: /Users/betacage/packages/midas/build
Darrens-Mac-mini:build betacage$ make install 
[  1%] Built target mfeo
[  3%] Built target mfe
[  4%] Built target rmana
[  5%] Built target manao
[  6%] Built target mana
[  6%] Built target git_revision_h
[ 30%] Built target objlib
[ 31%] Built target midas
[ 32%] Built target rmanao
[ 32%] Built target objlib-c-compat
[ 32%] Built target midas-c-compat
[ 33%] Built target midas-shared
[ 35%] Built target rmlogger
[ 36%] Linking CXX executable mhttpd
Undefined symbols for architecture x86_64:
  "_OPENSSL_init_ssl", referenced from:
      _mg_mgr_init in mongoose6.cxx.o
  "_SSL_CTX_set_options", referenced from:
      _mg_set_ssl in mongoose6.cxx.o
ld: symbol(s) not found for architecture x86_64
clang: error: linker command failed with exit code 1 (use -v to see invocation)
make[2]: *** [progs/mhttpd] Error 1
make[1]: *** [progs/CMakeFiles/mhttpd.dir/all] Error 2
make: *** [all] Error 2


I hope that this is the right forum to submit this kind of reports.
Any idea what do I have to do to continue ? Thanks is advance !

Berta 

> > ... support for certbot
> 
> The certbot tool to use instead of certbot is this: https://github.com/ndilieto/uacme
> 
> K.O.


HI Stefan and Konstantin, 

Thanks a lot for your messages. Sorry for my late reply, I only work on this project from Tuesday to Thursdays. I have 
run " make cmake" instead of "cd build; cmake" and this is the output regarding mhttpd:

/Library/Developer/CommandLineTools/usr/bin/c++  -O2 -g -DNDEBUG -Wl,-search_paths_first -Wl,-
headerpad_max_install_names  CMakeFiles/mhttpd.dir/mhttpd.cxx.o CMakeFiles/mhttpd.dir/mongoose6.cxx.o 
CMakeFiles/mhttpd.dir/mgd.cxx.o CMakeFiles/mhttpd.dir/__/mscb/src/mscb.cxx.o  -o mhttpd  -lsqlite3 ../libmidas.a 
/usr/lib/libssl.dylib /usr/lib/libcrypto.dylib -lz -lsqlite3 /usr/lib/libssl.dylib /usr/lib/libcrypto.dylib -lz 
Undefined symbols for architecture x86_64:
  "_OPENSSL_init_ssl", referenced from:
      _mg_mgr_init in mongoose6.cxx.o
  "_SSL_CTX_set_options", referenced from:
      _mg_set_ssl in mongoose6.cxx.o
ld: symbol(s) not found for architecture x86_64
clang: error: linker command failed with exit code 1 (use -v to see invocation)


I see that in your outputs the openssl libs are in /opt/local/lib/ while mine are in /usr/lib/, and that is the only difference. 
I have checked that the libraries libssl.dylib and libcrypto.dylib are in my /usr/lib/, and indeed they are, so I don't 
understand the reason for the error, I will continue investigating. 

Thanks 

Berta 

Hi all, 

I have updated our daq computer to the latest OS 10.15 with the idea that then I will get all our daq 
programs running and will not need to update again in years to come. 
But now I am running unto even more problems trying to compile Midas. 
OS 10.15.3, Xcode 11.3 with commad line tools 

Darrens-Mac-mini:~ betacage$ cd packages/midas/build/
Darrens-Mac-mini:build betacage$ cmake .. 
-- MIDAS: cmake version: 3.16.3
-- The C compiler identification is AppleClang 11.0.0.11000033
-- The CXX compiler identification is AppleClang 11.0.0.11000033
-- Check for working C compiler: /Library/Developer/CommandLineTools/usr/bin/cc
-- Check for working C compiler: /Library/Developer/CommandLineTools/usr/bin/cc -- works
-- Detecting C compiler ABI info
-- Detecting C compiler ABI info - done
-- Detecting C compile features
-- Detecting C compile features - done
-- Check for working CXX compiler: /Library/Developer/CommandLineTools/usr/bin/c++
-- Check for working CXX compiler: /Library/Developer/CommandLineTools/usr/bin/c++ -- works
-- Detecting CXX compiler ABI info
-- Detecting CXX compiler ABI info - done
-- Detecting CXX compile features
-- Detecting CXX compile features - done
-- MIDAS: CMAKE_INSTALL_PREFIX: /Users/betacage/packages/midas
-- MIDAS: Found ROOT version 6.18/04
-- Found ZLIB: /usr/lib/libz.dylib  
-- MIDAS: Found ZLIB version 
-- MIDAS: Found OpenSSL version 1.1.1d
-- MIDAS: MySQL not found
-- MIDAS: ODBC not found
-- MIDAS: SQLITE not found
-- MIDAS: nvidia-smi not found
-- Found Git: /usr/bin/git (found version "2.21.0 (Apple Git-122.2)") 
-- MIDAS example/experiment: MIDAS in-tree-build
-- MIDAS: Found ZLIB version 
-- MIDAS example/experiment: Found ROOT version 6.18/04
-- Configuring done
-- Generating done
-- Build files have been written to: /Users/betacage/packages/midas/build
Darrens-Mac-mini:build betacage$ make install
[  1%] Building CXX object CMakeFiles/mfeo.dir/src/mfe.cxx.o
In file included from /Users/betacage/packages/midas/src/mfe.cxx:15:
In file included from /Users/betacage/packages/midas/include/mfe.h:13:
/Users/betacage/packages/midas/include/midas.h:159:10: fatal error: 'pthread.h' file not found
#include <pthread.h>
         ^~~~~~~~~~~
1 error generated.
make[2]: *** [CMakeFiles/mfeo.dir/src/mfe.cxx.o] Error 1
make[1]: *** [CMakeFiles/mfeo.dir/all] Error 2


I guess that I am maybe the first one trying to install MIDAS in this OS, so I am willing to help as much as I 
can with getting this going. I have found a solution to this by downgrading Xcode to version 10 
https://stackoverflow.com/questions/58524715/failing-to-compile-a-c-application-under-macos-catalina-10-15
If you don't have other solutions I will try to do that tomorrow.

Thanks 

Berta