Back Midas Rome Roody Rootana
  Midas DAQ System, Page 40 of 45  Not logged in ELOG logo
Entry  18 Aug 2005, Konstantin Olchanski, Info, minor changes to run transition code 
Minor changes to run transitions code:
- improve debug messages
- fail transition if cannot connect to one of the clients
    Reply  23 Dec 2005, Konstantin Olchanski, Bug Report, minor changes to run transition code 
> Minor changes to run transitions code:
> - fail transition if cannot connect to one of the clients
       Reply  24 Dec 2005, Stefan Ritt, Bug Report, minor changes to run transition code 
> I am now considering allowing the run to end even if some clients cannot be
> contacted. The begin, pause and resume transitions would continue to fail if
> clients cannot be contacted.
Entry  22 Dec 2005, Konstantin Olchanski, Info, midas max event size? 
My TPC events are fairly large: 18 FEC cards * 128 channels per card * 2 Kbytes
per channel = about 4 Mbytes. In my
frontend, when I request this event size, MIDAS complaints (in mfe.c) that it is
    Reply  23 Dec 2005, Stefan Ritt, Info, midas max event size? 
> My TPC events are fairly large: 18 FEC cards * 128 channels per card * 2 Kbytes
> per channel = about 4 Mbytes. In my
> frontend, when I request this event size, MIDAS complaints (in mfe.c) that it is
Entry  14 Dec 2005, Konstantin Olchanski, Bug Report, misc problems 
I would like to document a few problems I ran into while setting up a new
experiment (two USB interfaces to Alice TPC electronics, plus maybe a USB
interface to CAMAC). I am using a midas cvs checkout from last October, so I am
Entry  02 Dec 2005, Greg Hackman, Info, MIDAS on Cygwin 
If you want to run MIDAS on Cygwin, make sure you have cygserver running.  First set a Windows system environment variable CYGWIN=server.  This is best
done through the Control Panel -> System -> Advanced -> Environment Variables.  Then run /usr/bin/cygserver-config in a Cygwin console window.  Then reboot.
 After that your MIDAS executables should run properly.
Entry  23 Nov 2005, Stefan Ritt, Bug Fix, Endian swapping in mana.c 
It was reported that following code in mana.c :

[code]
Entry  02 Nov 2005, Stefan Ritt, Suggestion, Where to put drivers? 
Hi,

I would like to raise the question where to put the midas drivers.
    Reply  06 Nov 2005, Pierre-Andre Amaudruz, Suggestion, Where to put drivers? 
[quote="Stefan Ritt"]Hi,

I would like to raise the question where to put the midas drivers.
       Reply  06 Nov 2005, Stefan Ritt, Suggestion, Where to put drivers? 
[quote="Stefan Ritt"]We have both the example experiment and the MSCB Makefile which both expect to find the midas drivers under [b]$MIDASSYS/drivers/camac[/b]
or [b]$MIDASSYS/drivers/usb[/b]. The documentation does not explicitely mention to define MIDASSYS as [b]/usr/local[/b], but some people do it. That however
requires to put all drivers then under [b]/usr/local/drivers[/b], which is not the case in the current Makefile for midas. Do you think that we should
Entry  23 Aug 2005, Konstantin Olchanski, Info, new mvmestd api 
For some time now, we have been thinking of updating the programming interface
for the VME bus interface drivers- mvmestd.h.
    Reply  01 Sep 2005, Stefan Ritt, Info, new mvmestd api 
Good that you brought up the MIDAS VME API again, since this is still not complete, but
has to be completed soon.
       Reply  01 Sep 2005, Stefan Ritt, Suggestion, new mvmestd api 
Anothe idea which comes to my mind, we could make it kind of object oriented, like

typedef struct {
       Reply  10 Sep 2005, Konstantin Olchanski, Info, new mvmestd api 
> Good that you brought up the MIDAS VME API again, since this is still not complete, but
> has to be completed soon.
          Reply  11 Sep 2005, Stefan Ritt, Info, new mvmestd api 
> Right, but I can only complete the parts that I thought of and for which I already have
> code. This leaves out support for DMA (read: any block transfers) and interrupts.
             Reply  02 Nov 2005, I. K. arapkorir, Info, new mvmestd api 
I manage to access some vme modules with the older vmicvme interface and seemed
confused with the
new interface as the sample code provided does not have a specific test sample.
                Reply  02 Nov 2005, Pierre-Andre Amaudruz, Info, new mvmestd api 
> I manage to access some vme modules with the older vmicvme interface and seemed
> confused with the
> new interface as the sample code provided does not have a specific test sample.
Entry  17 Oct 2005, Exaos Lee, Bug Fix, "make install" error under MacOS X 
Under MacOS X, "make install" will cours an error like this:
[code]
...
Entry  10 Oct 2005, Stefan Ritt, Info, Bus drivers moved in repository 
The previous midas/drivers/bus dirctory contains both midas slow control bus drivers plus vme & fastbus & camac drivers. I separated them now in different
directories:
    Reply  15 Oct 2005, Exaos Lee, Info, Bus drivers moved in repository 
The Makefile should be modified too. Please see the diff below:
[code]
diff Makefile Makefile.modify
Entry  07 Oct 2005, Stefan Ritt, Info, MIDAS moved from CVS to Subversion 
Dear Midas users,

I have moved midas from CVS to Subversion today. There were many reasons for doing so, which I don't want to explain in detail here. To use the new repository,
Entry  03 Oct 2005, Stefan Ritt, Info, Revised MVMESTD API 
Dear MIDAS users and developers,

The "Midas VME Standard API" has been revised. We tried to incorporate all
Entry  19 Sep 2005, Konstantin Olchanski, Info, Added driver for the Wiener CC-USB CAMAC interface 
Commited to CVS is the preliminary driver for the Wiener CC-USB CAMAC interface.
The driver implements all the mcstd.h camac access functions, except for those
not supported by hardware (8-bit operations, interrupts) and a few esoteric
Entry  18 Aug 2005, Konstantin Olchanski, Bug Fix, fix race condition between clients on run start/stop, pause/resume 
It turns out that the new priority sequencing of run state transitions had a
flaw: the frontends, the analyzer and the logger all registered at priority 500
and were invoked in essentially a random order. For example the frontend could
    Reply  01 Sep 2005, Stefan Ritt, Bug Fix, fix race condition between clients on run start/stop, pause/resume 
> It turns out that the new priority sequencing of run state transitions had a
> flaw: the frontends, the analyzer and the logger all registered at priority 500
> and were invoked in essentially a random order. For example the frontend could
Entry  18 Aug 2005, Konstantin Olchanski, Info, midas Makefile changes 
Minor Makefile changes:
- add "-m32" gcc flag to force 32-bit compilation on 64-bit Linux.
- do not link ybos.o into lazylogger and mdump.
Entry  02 Aug 2005, Konstantin Olchanski, Bug Fix, fix odb corruption when running analzer for the first time 
I have been plagued by ODB corruption when I run the analyzer for the first time
after setting up the new experiment. Some time ago, I traced this to
mana.c::book_ttree() and now I found and fixed the bug, fix now commited to
Entry  05 May 2005, Konstantin Olchanski, Bug Fix, fix: minor bit rot in the example experiment 
I fixed some minor bit rot in the example experiment: a few minor Makefile
problems, make the analyzer use the current histogram creation macros, etc. I
also added startup and shutdown scripts. These will be documented as we work
Entry  02 May 2005, Stefan Ritt, Info, strlcpy/strlcat moved into separate file 
I had to move strlcpy & strlcat into a separate file "strlcpy.c". A header file
"strlcpy.h" was added as well. This way one can omit the old HAVE_STRLCPY which
made life hard. The windows and linux makefiles were adjusted accordingly, but
Entry  21 Apr 2005, Konstantin Olchanski, Suggestion, Correct MIDASSYS setting? 
Current MIDAS versions nag me about setting the env.variable MIDASSYS to the
"midas installation directory", but I do not have one, so what should I set
MIDASSYS to? I checkout MIDAS from cvs into /home/olchansk/daq/midas, build it
    Reply  22 Apr 2005, Stefan Ritt, Suggestion, Correct MIDASSYS setting? 
> Current MIDAS versions nag me about setting the env.variable MIDASSYS to the
> "midas installation directory", but I do not have one, so what should I set
> MIDASSYS to? I checkout MIDAS from cvs into /home/olchansk/daq/midas, build it
Entry  05 Apr 2005, Donald Arseneau, Bug Report, pointers and segfault in yb_any_file_rclose 
I'm getting segfaults in yb_any_file_rclose (closing a file opened with
yb_any_file_ropen with type MIDAS).
    Reply  21 Apr 2005, Konstantin Olchanski, Bug Report, pointers and segfault in yb_any_file_rclose 
> I'm getting segfaults in yb_any_file_rclose (closing a file opened with
> yb_any_file_ropen with type MIDAS).
Entry  24 Mar 2005, Stefan Ritt, Info, ODB dump format switched to XML 
Dear midas users,

I have changed the ODB dump format to XML. As you might know, the logger writes
    Reply  29 Mar 2005, Stefan Ritt, Info, ODB dump format switched to XML 
> All the XML functionality is implemented in the new mxml.c/h library, which has
> been added to the distribution, and which can be used in other projects as well
> (XML configuration of ROODY?). It has already been successfully implemented in
       Reply  31 Mar 2005, Konstantin Olchanski, Info, ODB dump format switched to XML 
> > All the XML functionality is implemented in the new mxml.c/h library

> mxml.c/h ... I separated it's CVS tree.
          Reply  31 Mar 2005, Stefan Ritt, Info, ODB dump format switched to XML 
> Looks like the midas mxml Makefile bits did not make it to CVS. Current Makefile
> revision 1.67 does not have them and building midas from cvs sources fails because it
> does not find mxml.h and mxml.c
ELOG V3.1.4-2e1708b5